Mitsubishi Grandis. Manual — part 129
INPUT SIGNAL PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-513
Step 6. Check the wiring harness between C-129
remote controlled mirror switch connector
terminal No.4 and C-220 ETACS-ECU connector
terminal No.24.
• Check the input line for open circuit.
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Repair the wiring harness.
Step 7. Retest the system.
Check that the remote controlled mirror switch signal
is received normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
NO :
Replace the ETACS-ECU.
AC312031
AB
Connector: C-129
Harness side
<LHD>
AC312043AB
Connector: C-129 <RHD>
Harness side
AC312037
Connector: C-220
Junction block (Rear view)
AC
<LHD>
Harness side
AC312047
Connector: C-220
Junction block (Rear view)
AC
<RHD>
Harness side
INPUT SIGNAL PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-514
Inspection procedure Q-22: The interior lamp "all on" or "all off" switch signal is not sent to the
ETACS-ECU.
CAUTION
Whenever the ECU is replaced, ensure that the
input signal circuit is normal.
COMMENTS ON TROUBLE SYMPTOM
Input signals from the interior lamp "ON" and "OFF"
switch are used to operate the interior lamps (interior
lamp, rear personal lamp, luggage compartment
lamp, door lamps and key illumination lamp). If the
signals are abnormal, the interior lamps will not
illuminate and extinguish normally.
POSSIBLE CAUSES
• Malfunction of the interior lamp (interior lamp
switch)
• Malfunction of the ETACS-ECU
• Damaged harness wires and connectors
ETACS-ECU
ROOM LAMP
NOTE
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
RHD
LHD
Interior Lamp Input Circuit
INTERIOR
LAMP
SWITCH
INPUT SIGNAL PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-515
DIAGNOSTIC PROCEDURE
Step 1. Connector check: E-02 interior lamp
connector
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair the connector.
Step 2. Check the interior lamp.
Refer to GROUP 54A
− Interior lamp
.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Replace the interior lamp.
Step 3. Resistance measurement at the E-02
interior lamp connector.
(1) Disconnect the connector, and measure at the
AC312060
AB
Harness side
Connector: E-02
<Vehicles without sunroof-LHD>
AC312065
AB
Harness side
Connector: E-02
<Vehicles without sunroof-RHD>
AC312062
AD
Harness side
Connector: E-02
<Vehicles with sunroof-LHD>
AC312067
AD
Harness side
Connector: E-02
<Vehicles with sunroof-RHD>
AC312060
AB
Harness side
Connector: E-02
<Vehicles without sunroof-LHD>
AC312065
AB
Harness side
Connector: E-02
<Vehicles without sunroof-RHD>
AC312062
AD
Harness side
Connector: E-02
<Vehicles with sunroof-LHD>
AC312067
AD
Harness side
Connector: E-02
<Vehicles with sunroof-RHD>
INPUT SIGNAL PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-516
wiring harness side.
(2) Resistance between E-02 interior lamp connector
terminal No.5 and body earth
OK: 2
Ω or less
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Go to Step 4.
AC312730AQ
Connector E-02
(Harness side)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст