Mitsubishi Grandis. Manual — part 821
TAILGATE SPOILER
EXTERIOR
51-19
(1) Set the tape along the door frame, and overlay
it on the vertical tape by 2 mm.
(2) Peel off the upper area of the released paper,
and press the tape.
(3) While peeling off the remaining released paper
backward, press the tape along the frame line
with the fingers.
(4) Overlay the end of the tape on the vertical tape
by 2 mm.
(5) Roll in the tape into the inside not to get
wrinkled.
TAILGATE SPOILER
REMOVAL AND INSTALLATION
M1511019900091
AC303115AB
Door sash tape
Overlap:
2 mm
AC312064
3
4
1
2
5
AB
Removal steps
•
Tailgate upper trim (Refer to GROUP
52A, Tailgate trim
1. High-mounted stop lamp connector
connection
2. Rear washer hose connection
3. Tailgate spoiler assembly
4. High-mounted stop lamp assembly
5. Tailgate spoiler
Removal steps (Continued)
ROOF RAIL
EXTERIOR
51-20
ROOF RAIL
REMOVAL AND INSTALLATION
M1511016600217
AC313502
1
6
5
2
3
4
AB
B
B
A
A
C
C
C
C
D
D
E
E
AC302137
5
6
1
1
6
4
5
1
1
2
2
1
5, 6
4
AB
Section A – A
Section D – D
Section E – E
Section B – B
Section C – C
Claw
Claw
Claw
Claw
Claw
Claw
Claw
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-21
WINDSHIELD WIPER AND WASHER
SERVICE SPECIFICATION
M1511000300433
TROUBLESHOOTING
M1511020000177
The windshield wiper and washer are controlled by
the Smart Wiring System (SWS). For
troubleshooting, refer to GROUP 54B,
Troubleshooting
Troubleshooting
.
NOTE: Even when the ETACS-ECU has failed, the
windshield wiper can work at low speed as fail-safe
mode. (Normally, the windshield wiper operates
when the ignition switch is at the "ACC" position. But,
if it enters the fail-safe mode, the wiper can operate
only when the ignition switch is at the "ON" position.)
ON-VEHICLE SERVICE
WINDSHIELD INTERMITTENT WIPER
INSPECTION
M1511023600015
1. Check the wipers operate in the intermittent
action when the windshield intermittent wiper
switch is at the intermittent operation.
2. Check that the intermittent wiper interval is
changed as the intermittent wiper volume is
operated.
3. Turn the windshield intermittent wiper switch to
the intermittent operation position. Use the
MUT-III to set a simulated vehicle speed with the
wiper volume held. The intermittent wiper interval
should be changed as the simulated vehicle
speed is changed.
4. If either of above is defective, carry out the
troubleshooting. (Refer to GROUP 54B,
Troubleshooting
or GROUP 54C,
Troubleshooting
.)
WASHER MOTOR INSPECTION
(WINDSHIELD WASHER)
M1511019100675
1. Check the washer fluid level, and refill if
necessary.
2. Remove the splash shield.
3. Disconnect the washer motor connector.
4. Disconnect the front washer hose as shown.
5. Connect the battery to the washer motor
connector as shown. Check that the washer motor
delivers washer strongly.
Removal steps
•
Headlining assembly (Refer to
GROUP 52A, Headlining
1. Roof rail
2. Front packing
3. Centre packing
4. Rear packing
5. Front roof rail cover
6. Rear roof rail cover
Removal steps (Continued)
Item
Standard value
Stop position of the windshield wiper arm/blade assembly (Distance between
the edge of the wiper blade and the end of the deck garnish) mm
Driver’s side: 123
± 5
Passenger’s side: 25
± 5
AC303908
AB
Washer motor
Front washer hose
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-22
WINDSHIELD WIPER
REMOVAL AND INSTALLATION
M1511007900157
AC310899
3
1
7
9
AB
7.4 ± 1.4 N·m
30 ± 3 N·m
30 ± 3 N·m
4
4
2
3
2
7
8
5
6
7.4 ± 1.4 N·m
10
11
Roof drip moulding
Roof drip moulding
View A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст