Mitsubishi Grandis. Manual — part 820
DOOR SASH TAPE
EXTERIOR
51-15
(1) Align the tape with the specified application
position.
(2) Position it with a magnet, and secure with a
clip temporarily.
(3) Cut the released paper in the upper area of
the tape by approximately 100 mm, and
secure the tape temporarily.
(4) While peeling off the remaining released paper
downward, press the tape.
(5) Peel off the application tape upward in the
direction of 180 degrees.
(6) Press the folded area of the tape at 3 positions
(60 degrees, 120 degrees, and holding),
rolling in toward the vehicle inside direction.
(7) Finally roll in the A section with the palms.
AC303466
AB
4.5 mm
3.5 mm
RH only
Locating
point
Locating
point
Backing paper
cut-line
Backing paper
cut-line
AC303110AB
Backing paper
Door sash tape
AC303415
AB
MB990528
120˚
60˚
Hemming part
AC303443AB
A
Tape pasting onto corner
DOOR SASH TAPE
EXTERIOR
51-16
>>B<< REAR DOOR SASH OUTER TAPES
INSTALLATION
CAUTION
• The ambient temperature should be 20 to
30
°C. Ensure that the working area is clean.
Ideally, the tape application should be done at
ambient temperature of 25
°C.
• If ambient temperature is less than 15°C, heat
the tape and application surface to a
temperature of 20 to 30
°C. If ambient
temperature is 35
°C or higher, cool down
them.
• The adhesive property of the tape is
deteriorated at low temperature, so the tape
may come adrift easily. Meanwhile, it gets
softened at hot temperature.
• When beginning to apply the tape, pay
particular attention. If the end of the tape
cannot be applied to the specified position
with an accuracy of less than 1 mm, it may
cause the poor appearance or adhesion.
•
Use the special tool Stripe tape spatula with a
steady pace and pressure. If you do not apply
the tape with a steady pace or pressure, or
abort the application, a shallow groove
(lateral groove called as "Shock line") may be
present on the tape surface. Meanwhile, if you
apply it too quickly, air bubbles may be
formed under the tape.
1. Wrap a soft cloth (synthetic fiber) around the tip of
the special tool.
2. Use isopropyl alcohol to degrease the tape
application surface.
3. Wipe away dirt from the tape.
4. Apply the rear door sash outer (E) according to
the procedure below.
(1) Align the tape with the specified application
position.
(2) Position it with a magnet, and secure with a
clip temporarily.
(3) Peel off the released paper behind the cut line
in the vehicle rear side, and press the tape.
(4) While peeling off the remaining released paper
from vehicle rear to front, press the tape.
(5) Peel off the application tape in the direction of
180 degree from the applied direction.
(6) Press the folded area of the tape at 3 positions
(60 degrees, 120 degrees, and holding),
rolling in toward the vehicle inside direction.
5. Apply the door sash tape outer (C and D)
according to the procedure below.
AC303428
40 to 50˚
30 to 45˚
10 to 20 mm
10 to 20 mm
AB
MB990528
MB990528
Door sash tape
Door sash tape
Backing paper
Backing paper
<Pushing direction>
<Pulling direction>
3 to 7 cm/sec.
3 to 7 cm/sec.
AC303467
3.5 mm
AB
Overlap: 3mm
RH only
Locating
point
Backing paper
cut-line
AC303415
AB
MB990528
120˚
60˚
Hemming part
DOOR SASH TAPE
EXTERIOR
51-17
(1) Align the tape with the specified application
position.
(2) Position it with a magnet, and secure with a
clip temporarily.
(3) Cut the released paper in the upper area of
the tape by approximately 100 mm, and
secure the tape temporarily.
(4) While peeling off the remaining released paper
downward, press the tape.
(5) Peel off the application tape upward in the
direction of 180 degrees.
(6) Press the folded area of the tape at 3 positions
(60 degrees, 120 degrees, and holding),
rolling in toward the vehicle inside direction.
(7) Finally roll in the A section with the palms.
>>C<< FRONT DOOR SASH INNER
TAPES INSTALLATION
CAUTION
• The ambient temperature should be 20 to
30
°C. Ensure that the working area is clean.
• If ambient temperature is less than 15°C, heat
the tape and application surface to a
temperature of 20 to 30
°C. If ambient
temperature is 35
°C or higher, cool down
them.
• The adhesive property of the tape is
deteriorated at low temperature, so the tape
may come adrift easily. Meanwhile, it gets
softened at hot temperature.
• Ideally, the tape application should be done at
ambient temperature of 25
°C.
1. Use isopropyl alcohol to degrease the tape
application surface.
2. Wipe away dirt from the tape.
3. Apply the door sash tape inner (G) according to
the procedure below.
AC303468
AB
4.5 mm
3.5 mm
RH only
Locating
point
Locating
point
Backing paper
cut-line
Backing paper
cut-line
AC303110AB
Backing paper
Door sash tape
AC303415
AB
MB990528
120˚
60˚
Hemming part
AC303443AB
A
Tape pasting onto corner
DOOR SASH TAPE
EXTERIOR
51-18
(1) Fold the upper area of the tape by 1 mm, and
press it against the door frame.
(2) Peel off the upper area of the released paper,
and press the tape.
(3) While peeling off the remaining released paper
downward, press the tape along the frame line
with the fingers.
(4) Roll in the tape into the inside not to get
wrinkled.
4. Apply the door sash tape inner (F) according to
the procedure below.
(1) Press the tape against the door frame, and
overlay it on the vertical tape by 2 mm.
(2) Peel off the upper area of the released paper,
and press the tape.
(3) While peeling off the remaining released paper
downward, press the tape along the frame line
with the fingers.
(4) Roll in the tape into the inside not to get
wrinkled.
>>D<< REAR DOOR SASH INNER TAPES
INSTALLATION
CAUTION
• The ambient temperature should be 20 to
30
°C. Ensure that the working area is clean.
• If ambient temperature is less than 15°C, heat
the tape and application surface to a
temperature of 20 to 30
°C. If ambient
temperature is 35
°C or higher, cool down
them.
• The adhesive property of the tape is
deteriorated at low temperature, so the tape
may come adrift easily. Meanwhile, it gets
softened at hot temperature.
• Ideally, the tape application should be done at
ambient temperature of 25
°C.
1. Use isopropyl alcohol to degrease the tape
application surface.
2. Wipe away dirt from the tape.
3. Apply the door sash tapes (I and J) according to
the procedure below.
(1) Fold the upper area of the tape by 1 mm, and
press it against the door frame. Overlay it on
the vertical tape by 2 mm.
(2) Peel off the upper area of the released paper,
and press the tape.
(3) While peeling off the remaining released paper
downward, press the tape along the frame line
with the fingers.
(4) Roll in the tape into the inside not to get
wrinkled.
4. Apply the door sash tape (H) according to the
procedure below.
AC303114AB
Locating
point
Door sash tape
AC303505AB
Door sash tape
Overlap:
2 mm
AC303114AB
Locating
point
Door sash tape
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст