Mitsubishi Grandis. Manual — part 85
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-337
Step 21. Check the wiring harness from the
F-13-6 side turn-signal lamp (RH) connector
terminal No.1 to C-219 ETACS-ECU connector
terminal No.9 or F-07-6 side turn-signal lamp (LH)
connector terminal No.1 to C-219 ETACS-ECU
connector terminal No.14.
NOTE:
AC310626AD
Connector: C-219 <LHD>
Junction block (Rear view)
Junction block side
AC310620
Connector: C-219
Junction block
(Rear view)
<RHD>
AB
Junction block side
AC303049AF
Connector:
F-07-6
Harness side
1
2
AC303050AC
Connector:
F-13-6
Harness side
1
2
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-338
Prior to the wiring harness inspection, check
intermediate connector C-14 <side turn-signal lamp
(RH)>, C-27 <side turn-signal lamp (LH)> and
junction block connector C-205, and repair if
necessary.
• Check the output lines for open circuit.
Q: Is the check result normal?
YES :
Go to Step 22.
NO :
Repair the wiring harness.
Step 22. Retest the system.
Check that the side turn-signal lamps illuminate
normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
NO :
Replace the side turn-signal lamp.
AC310615
AB
Connector: C-14 <LHD>
AC310631
Connector: C-14 <RHD>
AG
AC310613
Connector: C-27 <LHD>
AJ
AC310628AN
Connector: C-27 <RHD>
AC310623
Connector: C-205 <LHD>
AM
Harness side
Junction block (Front view)
AC310618
Connectors: C-205 <RHD>
AL
Harness side
Junction block (Front view)
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-339
Step 23. Connector check: C-219 ETACS-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 24.
NO :
Repair the defective connector.
AC310626
Connector: C-219
Junction block (Rear view)
<LHD>
AB
Junction block side
AC310620
Connector: C-219
Junction block
(Rear view)
<RHD>
AB
Junction block side
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-340
Step 24. Check the wiring harness from the G-09
rear turn-signal lamp (RH) connector terminal
No.1 to C-219 ETACS-ECU connector terminal
No.9 or G-25 rear turn-signal lamp (LH)
connector terminal No.1 to C-219 ETACS-ECU
connector terminal or No.14.
NOTE:
Prior to the wiring harness inspection, check
intermediate connector G-21 and junction block
connector C-210, and repair if necessary.
• Check the output lines for open circuit.
Q: Is the check result normal?
YES :
Go to Step 25.
NO :
Repair the wiring harness.
AC310626
Connector: C-219
Junction block (Rear view)
<LHD>
AB
Junction block side
AC310620
Connector: C-219
Junction block
(Rear view)
<RHD>
AB
Junction block side
AC310222
Connector: G-09
AG
Harness side
G-09 (B)
AC310220
Connector: G-25
AF
G-25 (B)
Harness side
AC310623
Connector: C-210 <LHD>
AS
Harness side
Junction block (Front view)
AC310618
Connector: C-210 <RHD>
AQ
Harness side
Junction block (Front view)
AC310220
Connector: G-21 <LHD>
AC
AC310220
AC310220
Connector: G-21 <RHD>
AG
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст