Mitsubishi Grandis. Manual — part 982
STEERING SHAFT
POWER STEERING
37-18
DISASSEMBLY AND ASSEMBLY
M1372011700151
DISASSEMBLY SERVICE POINT
<<A>> STEERING LOCK REMOVAL
1. Drill in the special bolt a hole deep enough for the
tap to stand.
2. Remove the special bolt with a left-hand tap.
REASSEMBLY SERVICE POINT
>>A<< ENGINE STARTING SWITCH
ASSEMBLY / ENGINE STARTING SWITCH
BRACKET / STEERING LOCK
INSTALLATION
CAUTION
The steering lock bracket and bolts must be
replaced with new ones when the steering lock is
installed.
1. When installing the steering lock cylinder
assembly and steering lock bracket to the column
tube, temporarily install the steering lock in
alignment with the column boss.
2. After checking that the lock works properly,
tighten the special bolts until the head twists off.
AC302639AC
3
2
1
4
Disassembly steps
<<A>> >>A<<
1.
Steering locking bolt
>>A<<
2.
Engine starting switch bracket
>>A<<
3.
Engine starting switch assembly
4.
Steering column shaft assembly
ACX01138 AB
Steering lock
bracket
Reverse screw tap
Special bolt
Steering lock
cylinder
ACX01139 AB
POWER STEERING GEAR BOX AND LINKAGE
POWER STEERING
37-19
POWER STEERING GEAR BOX AND LINKAGE
REMOVAL AND INSTALLATION
M1372010900345
WARNING
Before removing the steering gear, refer to GROUP 52B, Service Precautions (
) and
Driver’s, Front Passenger’s Air Bag Module(s) and Clock Spring (
). Centre the front
wheels. Failure to do so may damage the SRS clock spring and render the SRS system
inoperative, risking serious injury.
CAUTION
• *
1
indicates parts which should be temporarily tightened, and then fully tightened with the engine
and transmission assembly weight applied on the vehicle body.
• *
2
indicates parts which should be temporarily tightened, and then fully tightened with the vehicle
standing on the ground and the curb weight condition.
Pre-removal Operation
• Power Steering Fluid Draining (Refer to
.)
• Centre member removal (Refer to GROUP 32, Engine roll
stopper and centre member
.)
• Exhaust pre-muffler removal (Refer to GROUP 15,
Exhaust pipe and main muffler
• Steering wheel assembly and air bag module assembly
removal (Refer to
).
Post-installation Operation
• Centre member installation (Refer to GROUP 32, Engine
roll stopper and centre member
• Exhaust pre-muffler installation (Refer to GROUP 15,
Exhaust pipe and main muffler
• Steering wheel assembly and air bag module assembly
).
• Power steering fluid refilling and air bleeding (Refer to
• Check the dust cover for crack or damage by pressing
your finger.
• Checking Steering Wheel Position with Wheels Straight
Ahead.
• Front Wheel Alignment Adjustment (Refer to GROUP 33,
On-vehicle Service
− Front Wheel Alignment Check and
Adjustment
POWER STEERING GEAR BOX AND LINKAGE
POWER STEERING
37-20
AC312227
6
108 ± 10 N·m
29 ± 4 N·m
89 ± 9 N·m
89 ± 9 N·m
75 ± 5 N·m
90 ± 10 N·m
90 ± 10 N·m
123 ± 12 N·m
123 ± 12 N·m
12 ± 2 N·m
57 ± 7 N·m
50 ± 10 N·m
57 ± 7 N·m
13 ± 2 N·m
18 ± 2 N·m
5.0 ± 1.0 N·m
69 ± 9 N·m
10
3
20
20
4
1
2
19
18
15
16
21
7
13
5
N
N
N
N
1
1
2
AB
9
11
22
17
14
8
7
N
12
N
13 ± 2 N·m
<LH drive vehicles>
Removal steps
<<A>>
1. Self-locking nut (tie rod end and
knuckle connection)
2. Self-locking nut (lower arm and
knuckle connection)
3. Lower arm assembly
4. Stabilizer link
5. Power steering oil pressure sensor
connector connection and harness
clamp
6. Eye bolt
7. Gasket
8. Pressure hose connection
>>C<<
9. Return tube connection
>>B<<
10. Return hose connection
11. Return tube connection
12. O-ring
13. Steering gear and joint connecting bolt
>>A<<
14. Steering column grommet
15. Selflock nut
16. Engine rear roll stopper bracket
connecting bolt
17. Crossmember rear stay
18. Lower stopper
<<B>>
19. Front axle No.1 crossmember
assembly
20. Stopper
21. Engine roll stopper
21. Steering gear and linkage
Removal steps (Continued)
POWER STEERING GEAR BOX AND LINKAGE
POWER STEERING
37-21
AC303001
6
108 ± 10 N·m
29 ± 4 N·m
89 ± 9 N·m
89 ± 9 N·m
75 ± 5 N·m
90 ± 10 N·m
90 ± 10 N·m
123 ± 12 N·m
123 ± 12 N·m
12 ± 2 N·m
57 ± 7 N·m
50 ± 10 N·m
57 ± 7 N·m
13 ± 2 N·m
18 ± 2 N·m
5.0 ± 1.0 N·m
69 ± 9 N·m
9
3
18
18
4
1
2
17
16
13
14
19
7
11
5
N
N
N
N
1
1
2
AC
8
10
20
15
12
<RH drive vehicles>
Removal steps
<<A>>
1. Self-locking nut (tie rod end and
knuckle connection)
2. Self-locking nut (lower arm and
knuckle connection)
3. Lower arm assembly
4. Stabilizer link
5. Power steering oil pressure sensor
connector connection and harness
clamp
6. Eye bolt
7. Gasket
8. Pressure hose connection
>>B<<
9. Return hose connection
10. Steering dust cover
11. Steering gear and joint connecting bolt
>>A<<
12. Steering column grommet
13. Selflock nut
14. Engine rear roll stopper bracket
connecting bolt
15. Crossmember rear stay
16. Lower stopper
<<B>>
17. Front axle No.1 crossmember
assembly
18. Stopper
19. Engine roll stopper
20. Steering gear and linkage
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст