Mitsubishi Grandis. Manual — part 676
DOOR
BODY
42-32
INSTALLATION SERVICE POINT
>>A<< STRIKER INSTALLATION
Align the centre of the striker and latch within
±1.5
mm, and install.
INSPECTION
M1423006000388
DOOR SWITCH CHECK
Striker removal steps
>>A<<
9.
Striker
10. Striker shim
Door switch removal steps
11. Door switch cover
12. Door switch
AC006126AC
+1.5 mm
-1.5 mm
Striker centre
Striker
Latch centre
Latch
Switch position Tester
connection
Specified
condition
Released (ON)
1
− switch body,
2
− switch body
Less than 2
ohms
Depressed
(OFF)
1
− switch body,
2
− switch body
Open circuit
AC303195 AB
ON
OFF
DOOR
BODY
42-33
DOOR GLASS AND REGULATOR
REMOVAL AND INSTALLATION
M1429001300456
Pre-removal Operation
• Door Trim Assembly Removal (Refer to GROUP 52A,
Door Trim
• Waterproof Film Removal (Refer to
Post-installation Operation
• Door Window Glass Adjustment (Refer to
• Waterproof Film Installation (Refer to
).
• Door Trim Assembly Installation (Refer to GROUP 52A,
Door Trim
AC310917
AC302998
AC302970
AC301997
AB
<Front door>
5.0 ± 1.0 N·m
5.4 ± 1.4 N·m
9.0 ± 2.0 N·m
9.0 ± 2.0 N·m
1
2
3
4
4
5
6
7
Power switch removal
1.
Power window main switch
<Driver’s side> and power window
sub switch <Passenger’s side>
(Refer to GROUP 52A, Door Trim
Door window glass assembly
removal steps
•
Door beltline moulding and Door
beltline inner weatherstrip (Refer to
2.
Door window glass assembly
3.
Glass holder
Power window regulator removal
steps
>>A<<
•
Post-installation operation check
<<A>>
4.
Power window regulator
5.
Power window motor
DOOR
BODY
42-34
Front lower sash removal steps
2.
Door window glass assembly
<<A>>
4.
Power window regulator
•
Door window glass runchannel
(Refer to
).
>>B<<
6.
Front lower sash
Rear lower sash removal steps
2.
Door window glass assembly
<<A>>
4.
Power window regulator
•
Door window glass runchannel
(Refer to
).
7.
Rear lower sash
AC302971
AC302999
AC310918
AC301998
1
2
3
4
5
5
6
AB
<Rear door>
5.4 ± 1.4 N·m
9.0 ± 2.0 N·m
5.0 ± 1.0 N·m
Power window sub switch
removal
1.
Power window sub switch (Refer to
GROUP 52A, Door Trim
Door window glass assembly
removal steps
•
Door beltline moulding and Door
beltline inner weatherstrip (Refer to
>>B<<
2.
Rear lower sash
3.
Door window glass assembly
4.
Glass holder
DOOR
BODY
42-35
REMOVAL SERVICE POINT
<<A>> POWER WINDOW REGULATOR
REMOVAL
1. Remove the door window glass installation bolts.
CAUTION
If tinting film is adhered to the door window
glass, attach special tool window glass holder
MB990480 to the outside of the glass to prevent
the film from peeling off.
2. Lift the door window glass, and attach special tool
window glass holder MB990480 to the glass as
shown to prevent the glass from falling.
3. Remove the window regulator.
INSTALLATION SERVICE POINTS
>>A<< POST-INSTALLATION OPERATION
CHECK
When the following procedures are carried out, make
the power window switch learn the fully closed
position of the power window (Refer to
• Power window regulator removal or replacement
• Power window switch removal or replacement
>>B<< REAR LOWER SASH AND FRONT
LOWER SASH INSTALLATION
Engage the rear lower sash and the front lower sash
with the window sash (door) securely.
INSPECTION
M1429001400378
HOW TO MAKE THE POWER WINDOW
SWITCH LEARN THE FULLY CLOSED
POSITION OF THE POWER WINDOW
HOW TO MAKE THE POWER WINDOW
SWITCH LEARN THE FULLY CLOSED
POSITION WHEN THE POWER WINDOW
SWITCH IS REMOVED, OR THE POWER
WINDOW REGULATOR ASSEMBLY IS
REMOVED OR REPLACED
1. If the anti-trap function (safety mechanism) is
activated consecutively three times or more, the
fully closed position that the power window switch
has learned will be erased (initialised).
2. Operate the power window switch and fully open
the door window glass.
CAUTION
The anti-trap function does not work until the
power window switch completes learning the
fully closed position (It is because the anti-trap
function is reset).
3. Operate the power window switch and fully close
the door window glass. The power window
activates for 0.7 seconds and stops automatically
when the power window switch is pressed once.
Repeat this operation until the door window glass
fully closes and release the switch once. Then,
hold the power window switch to the fully closed
side again for one second so that the power
window switch completes learning the fully closed
position.
NOTE: If the power window switch is operated to
open the door window glass while the switch is
learning, learning will be cancelled. If this
happens, return to step 2.
HOW TO MAKE THE POWER WINDOW
SWITCH LEARN THE FULLY CLOSED
POSITION WHEN THE POWER WINDOW
SWITCH IS REPLACED WITH A NEW ONE
CAUTION
The anti-trap function does not work until the
power window switch completes learning the
fully closed position (It is because the anti-trap
function is reset).
Operate the power window main switch to fully close
the door window glass by one-shot up action so that
the power window switch will complete learning
(Initialisation is not needed).
Power window regulator removal
steps
>>A<<
•
Post-installation operation check
<<A>>
5.
Power window regulator
6.
Power window motor
AC100009AC
MB990480
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст