Mitsubishi Grandis. Manual — part 677

DOOR

BODY

42-36

NOTE: When the power window sub switch of each
seat is replaced, operate the power window main
switch to fully close the applicable power window by
one-shot up action (It is because the power window
sub switch does not have one-shot up/down
function).

DOOR HANDLE AND LATCH

REMOVAL AND INSTALLATION

M1423004600470

Pre-removal Operation
• Door Trim Assembly Removal (Refer to GROUP 52A,

Door Trim

P.52A-12

).

Post-installation Operation
• Door Inside Handle Play Check (Refer to

P.42-29

).

• Door Outside Handle Play Check (Refer to

P.42-29

).

• Door Trim Assembly Installation (Refer to GROUP 52A,

Door Trim

P.52A-12

).

AC303146

AC310940

AC302891

AC208142

1

1

2

3

4

5

6

7

8

8

9

10

AB

<Front door>

5.0 ± 1.0 N·m

5.0 ± 1.0 N·m

5.0 ± 1.0 N·m

5.0 ± 1.0 N·m

24 ± 4 N·m

N

Door handle and door latch
removal steps

>>B<<

1.

Door inside handle

•

Rear lower sash (Refer to

P.42-33

).

2.

Screw

3.

Door latch assembly

4.

Inside lock cable

5.

Inside handle cable

6.

Outside handle rod

7.

Key cylinder

8.

Door outside handle

Door handle and door latch
removal steps (Continued)

DOOR

BODY

42-37

Door check removal steps

•

Waterproof film (Refer to

P.42-40

).

•

Front lower sash (Refer to

P.42-33

).

>>A<<

9.

Door check
Door panel core removal steps

•

Power window regulator (Refer to

P.42-33

).

10. Door panel core

AC303147

AC310941

AC302891

AC208142

1

1

2

2

3

4

5

6

7

8

AB

<Rear door>

5.0 ± 1.0 N·m

5.0 ± 1.0 N·m

5.0 ± 1.0 N·m

24 ± 4 N·m

N

Door handle and door check
removal steps

>>B<<

1.

Door inside handle

•

Waterproof film (Refer to

P.42-40

).

2.

Door outside handle

•

Rear lower sash (Refer to

P.42-33

).

3.

Screw

4.

Door latch assembly

5.

Inside lock cable

6.

Inside handle cable

7.

Outside handle rod
Door check removal steps

•

Waterproof film (Refer to

P.42-40

).

>>A<<

8.

Door check

Door handle and door check
removal steps (Continued)

DOOR

BODY

42-38

INSTALLATION SERVICE POINTS
>>A<< DOOR CHECK INSTALLATION

Install the door check with the following identification
marks facing upward.

>>B<< DOOR INSIDE HANDLE
INSTALLATION

When connecting the inside cable to the door inside
handle, ensure that the door latch and the inside
handle are unlocked.

INSPECTION

M1423004700563

FRONT DOOR LOCK ACTUATOR CHECK

ACTUATOR OPERATION CHECK

Item

Identification
mark

Front Door

Left side

55L

Right side

55R

Rear Door

Left side

56L

Right side

56R

AC302892 AB

A

Identification mark

View A

Lever
position

Battery connection Lever

operation

At the
"LOCK"
position

• Connect terminal

No.4 and the
negative battery
terminal.

• Connect terminal

No.6 and the
positive battery
terminal.

The lever
moves from the
"LOCK"
position to the
"UNLOCK"
position.

At the
"UNLOCK"
position

• Connect terminal

No.6 and the
negative battery
terminal.

• Connect terminal

No.4 and the
positive battery
terminal.

The lever
moves from the
"UNLOCK"
position to the
"LOCK"
position.

4

2
5

3
6

1

4

2
5

3
6

1

AC208145

B

A

AB

Lever

UNLOCK

<Front left side>

<Front right side>

LOCK

View A

Lever

UNLOCK

LOCK

View B

DOOR

BODY

42-39

ACTUATOR SWITCH CHECK <DRIVER’S SIDE
(LH DRIVE VEHICLES)>

ACTUATOR SWITCH CHECK <DRIVER’S SIDE
(RH DRIVE VEHICLES)>

REAR DOOR LOCK ACTUATOR CHECK

ACTUATOR OPERATION CHECK

DOOR LOCK KEY CYLINDER SWITCH
CHECK <PASSENGER’S SIDE>

<LH DRIVER VEHICLES>

Lever position Tester

connection

Specified
condition

At the "LOCK"
position

1

− 2

Less than 2
ohms

At the
"UNLOCK"
position

1

− 3

Less than 2
ohms

Lever position Tester

connection

Specified
condition

At the "LOCK"
position

2

− 3

Less than 2
ohms

At the
"UNLOCK"
position

1

− 3

Less than 2
ohms

4

2
5

3
6

1

AC208587

4

2
5

3
6

1

B

A

AB

Lever

UNLOCK

LOCK

Lever

UNLOCK

LOCK

<Rear left side>

<Rear right side>

View A

View B

Lever
position

Battery connection

Lever
operation

At the
"LOCK"
position

• Connect terminal

No.4 and the
negative battery
terminal.

• Connect terminal

No.6 and the
positive battery
terminal.

The lever
moves from
the "LOCK"
position to the
"UNLOCK"
position.

At the
"UNLOCK"
position

• Connect terminal

No.6 and the
negative battery
terminal.

• Connect terminal

No.4 and the
positive battery
terminal.

The lever
moves from
the "UNLOCK"
position to the
"LOCK"
position.

Switch
position

Tester
connection

Specified
condition

LOCK

2

− 3

Less than 2
ohms

UNLOCK

1

− 3

Less than 2
ohms

AC310942

AC303028

A

AB

View A

LOCK

UNLOCK