Mitsubishi Grandis. Manual — part 79
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-313
Step 5. Retest the system.
Check that the turn-signal lamps illuminate normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
NO :
Replace the ETACS-ECU.
Step 6. Pulse check
Check the input signals below, which are related to
the turn-signal lamp illumination.
OK: The MUT-III sounds or the voltmeter
needle fluctuates.
Q: Are the check result normal?
All the signals are received normally. :
Go to Step
The turn-signal lamp switch (RH) signal is not
received. :
Refer to inspection procedure Q-6 "The
column switch (lighting and turn-signal lamp
switch) signal is not received
The turn-signal lamp switch (LH) signal is not
received. :
Refer to inspection procedure Q-6 "The
column switch (lighting and turn-signal lamp
and headlamp washer switch) signal is not
received
."
Step 7. Retest the system.
Check that the turn-signal lamps illuminate.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
NO :
Replace the ETACS-ECU.
System switch
Check condition
Turn-signal lamp switch
(RH)
When the turn-signal
lamp switch (RH) is
turned from off to on
Turn-signal lamp switch
(LH)
When the turn-signal
lamp switch (LH) is
turned from off to on
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-314
Inspection Procedure N-2: The hazard warning lamps do not illuminate.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
COMMENTS ON TROUBLE SYMPTOM
If the hazard warning lamps do not illuminate, the
hazard warning lamp input signal circuit or the
ETACS-ECU may be defective.
POSSIBLE CAUSES
• Malfunction of the hazard warning lamp switch
• Malfunction of the ETACS-ECU
• Damaged harness wires and connectors
DIAGNOSTIC PROCEDURE
Step 1. Check that the turn-signal lamps operate.
Check that the turn-signal lamps illuminate normally.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Refer to inspection procedure N-1 "The
turn-signal lamps do not illuminate
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
ETACS-ECU
HAZARD
WARNING
LAMP SWITCH
RELAY
BOX
TURN-SIGNAL
LAMP RELAY: LH
TURN-SIGNAL
LAMP RELAY: RH
INPUT SIGNAL
· FRONT TURN-SIGNAL
LAMP (LH)
· SIDE TURN-SIGNAL
LAMP (LH)
· REAR TURN-SIGNAL
LAMP (LH)
· FRONT TURN-SIGNAL
LAMP (RH)
· SIDE TURN-SIGNAL
LAMP (RH)
· REAR TURN-SIGNAL
LAMP (RH)
J/B SIDE
FUSIBLE
LINK
26
Hazard Warning Lamp Circuit
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-315
Step 2. Check the power supply circuit.
When the ignition switch is at the LOCK (OFF)
position, check that the functions below work
normally.
• Lamp reminder function
• Central door locking system
• Room lamp (excluding interior lamp
automatic-shutdown function)
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Refer to inspection procedure A-2 "Check
the ETACS-ECU battery power supply
circuit
Step 3. Pulse check
Check the input signal from the hazard warning lamp
switch.
OK: The MUT-III sounds or the voltmeter
needle fluctuates.
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Refer to inspection procedure Q-12 "The
hazard warning lamp switch signal is not
received
."
Step 4. Retest the system.
Check that the hazard warning lamps illuminate.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
NO :
Replace the ETACS-ECU.
System switch
Check condition
Hazard warning lamp
switch
When the hazard
warning lamp switch is
turned from off to on
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-316
Inspection Procedure N-3: Any of the turn-signal lamps does not illuminate.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст