Mitsubishi Grandis. Manual — part 398
SPECIAL TOOLS
REAR AXLE
27-3
SPECIAL TOOLS
M1271000600558
ON-VEHICLE SERVICE
WHEEL BEARING AXIAL PLAY CHECK
M1271000900504
1. Remove the caliper assembly, and suspend the
caliper assembly with a wire and remove the
brake disc.
2. Check the bearing's axial play. Place a dial gauge
against the hub surface; then move the hub in the
axial direction and check whether or not there is
axial play.
Limit: 0.05 mm
3. If the play exceeds the limit, replace the rear hub
assembly.
4. After having checked, install the brake disc, the
caliper assembly and tighten the caliper mounting
bolt to the specified torque.
Tightening torque: 60
± 5 N⋅m
WHEEL BEARING ROTARY-SLIDING
RESISTANCE CHECK
M1271001100299
1. Remove the caliper assembly, and suspend the
caliper assembly with a wire and remove the
brake disc.
2. Turn the hub a few times to seat the bearing.
3. Wind a rope around the hub bolt and turn the hub
by pulling at a 90
° angle with a spring balance.
Measure to determine whether or not the
rotary-sliding resistance of the wheel bearing is at
the limit value.
Limit: 19 N
4. If limit value is exceeded, replace the rear hub
assembly.
5. After having checked, install the brake disc, the
caliper assembly and tighten the caliper mounting
bolt to the specified torque.
Tightening torque: 60
± 5 N⋅m
Tool
Number
Name
Use
MB990767
End yoke holder
Hub fixing
MB991618
Hub bolt remover
Hub bolt removal
B990767
MB991618
AC302112 AC
AC302113
ON-VEHICLE SERVICE
REAR AXLE
27-4
HUB BOLT REPLACEMENT
M1271001000300
1. Remove the caliper assembly, and suspend the
caliper assembly with a wire and remove the
brake disc.
2. Use the following special tools to remove the hub
bolts.
• End yoke holder (MB990767)
• Hub bolt remover (MB991618)
NOTE: To retain a space for removing the hub
bolts, remove them near the retainer spring
mounting position.
3. Install the plain washer to the new hub bolt, and
install the bolt with a nut.
AC301662
MB990767
MB991618
AB
AC301663
MB990767
AB
Plain
washer
REAR AXLE HUB ASSEMBLY
REAR AXLE
27-5
REAR AXLE HUB ASSEMBLY
REMOVAL AND INSTALLATION
M1271002000433
CAUTION
• Do not disassemble the rear wheel hub assembly.
• The vehicle speed detection magnetic encoder collects any metallic particle easily, because it is
magnetised.Make sure that the magnetic encoder should not collect any metallic particle. Check
that there is not any trouble prior to reassembling it.
• When the rear wheel hub assembly is removed and installed, make sure that the vehicle speed
detection magnetic encoder does not contact with surrounding parts to avoid damage.
• When the rear wheel speed sensor is removed and installed, make sure that its pole piece does
not contact with surrounding parts to avoid damage.
REMOVAL SERVICE POINTS
<<A>> CALIPER ASSEMBLY REMOVAL
Secure the removed caliper assembly with wire, etc.
<<B>> BRAKE DISC REMOVAL
If the brake disc is seized, install M8
× 1.25 bolts as
shown, and remove the disc by tightening the bolts
evenly and gradually.
INSPECTION
M1271002100281
• Check the rear hub assembly for crack or
damage.
AC311498 AB
4
1
3
60 ± 5 N·m
2
55 ± 5 N·m
Vehicle
speed
detection
magnetic
encoder
Removal steps
1.
Rear wheel speed sensor
<<A>>
2.
Caliper assembly
<<B>>
3.
Brake disc
4.
Rear wheel hub assembly
AC302117AC
Bolts
(M8×1.25)
00-1
GROUP 00
GENERAL
CONTENTS
HOW TO USE THIS MANUAL. . . . . .
HOW TO USE
TROUBLESHOOTING/INSPECTION SERVICE
POINTS . . . . . . . . . . . . . . . . . . . . . . .
VEHICLE IDENTIFICATION . . . . . . .
GENERAL DATA AND SPECIFICATIONS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PRECAUTIONS BEFORE SERVICE.
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
AND SEAT BELT WITH PRE-TENSIONER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SERVICE PRECAUTIONS . . . . . . . . .
SUPPORT LOCATIONS FOR LIFTING AND
JACKING . . . . . . . . . . . . . . . . . . . . . .
TOWING AND HOISTING. . . . . . . . . .
STANDARD PART/TIGHTENING-TORQUE
TABLE. . . . . . . . . . . . . . . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст