Mitsubishi Outlander (2013+). Manual — part 570
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-39
WINDSHIELD WIPER
REMOVAL AND INSTALLATION
M1511007901525
ACB05595AB
2
8
27 ± 3 N·m
1
3
2
7
27 ± 3 N·m
1
3
8.0 ± 2.0 N·m
8.0 ± 2.0 N·m
5
4
4
B
B
A
A
6
ACC00219AB
Section B – B
4
Section A – A
Clip
Claw
Windshield
Front fender
Claw
4
Windshield
Claw
Front fender
Wiper blade removal steps
1.
Wiper blade assembly
>>
C
<<
2.
Wiper blade
Windshield wiper motor removal
steps
>>
B
<<
3.
Wiper arm and blade assembly
4.
Front deck garnish cover
5.
Front deck garnish
<<
A
>>
>>
A
<<
6.
Windshield wiper link assembly
7.
Windshield wiper link
8.
Windshield wiper motor
NOTE: For removal and installation of the wiper and
washer switch, refer to GROUP 54A, Column Switch
.
Windshield wiper motor removal
steps (Continued)
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-40
REMOVAL SERVICE POINT
<<A>> WINDSHIELD WIPER LINK
ASSEMBLY REMOVAL
CAUTION
When pulling out the link assembly forward, be
careful not to make a contact with the windshield
glass.
ACB05637
Rubber bush
AB
1. Remove the rubber bushing of the windshield
wiper link assembly in the direction of the arrow
from the windshield wiper bracket.
INSTALLATION SERVICE POINTS
>>A<< WINDSHIELD WIPER LINK
ASSEMBLY INSTALLATION
1. Confirm that the wiper motor has set to automatic
stop position (Refer to
CAUTION
Always replace the wiper motor link plate with
new one.
ACC00454AB
Wiper motor
link plate
Link rod
2. Set the wiper motor link plate onto the wiper motor
shaft. When doing this, the wiper motor link plate
and the wiper link rod should be in line as shown.
NOTE: When the wiper motor link plate has
slipped by even only one tooth on the wiper motor
assembly, they cannot be in line.
3. Tighten the attaching nut of wiper motor link plate
and wiper motor shaft. Use an appropriate tool to
counter-hold the plate to prevent it from turning.
4. Apply grease to the inside of link rod joint (as
required) and connect the link rod to wiper motor
link plate.
Specified grease: Multipurpose grease SAE
J310, NLGI No.2 or equivalent
ACB05637
Rubber bush
AC
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-41
5. Make sure that the rubber bushing of the
windshield wiper linkage assembly is secured in
the windshield wiper bracket.
>>B<< WIPER ARM AND BLADE
ASSEMBLY INSTALLATION
ACB05628AB
Ø2 marking
B
B
Ø2 marking
A
ACB05630
ACB05629
ACC00474AB
Ø2 marking
5
Section B – B
Unit: mm
5
View A
Ø2 marking
5
5
Unit: mm
Install the wiper arm and blade assembly at the
specified positions.
Standard value
(A):
φ 2 marking ± 5 mm
>>C<< WIPER BLADE INSTALLATION
AC101090
AE
A
A
Wiper blade
Backing
Backing
Section A – A
Wiper
blade
Backing
CAUTION
Use a curved backing like that shown for the
backing of a wiper blade to ensure sustained
wiper wiping performance.
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-42
INSPECTION
M1511019103674
WINDSHIELD WIPER MOTOR CHECK
4
5
3
1 2
4
5
3
1 2
ACC00156
4
5
3
1 2
AB
Operation check
Low speed
High speed
Remove the windshield wiper motor and inspect it at
the harness connector.
WINDSHIELD WIPER MOTOR AT LOW OR
HIGH SPEED OPERATION
Connect the battery to the windshield wiper motor to
inspect the operation of motor rotation at low or high
speed.
4
5
3
1 2
4
5
3
1 2
ACC00156
4
5
3
1 2
AC
(B) Automatic stop
(A) Low speed
Stop position check
WINDSHIELD WIPER MOTOR AT STOP
POSITION OPERATION
1. Connect the battery to the windshield wiper motor
as shown in the illustration (A).
2. Run the windshield wiper motor at low speed,
then disconnect the battery in the middle of the
motor rotation and check to see that the motor
stops.
3. Connect the battery to the windshield wiper motor
as shown in the illustration (B).
4. Connect the terminals of the windshield wiper
motor connector as shown in the illustration (B).
5. Check to see that the windshield wiper motor runs
at low speed and then stops at the automatic stop
position.
WINDSHIELD WIPER SWITCH CHECK
Check the windshield wiper switch (mist, intermittent,
low speed and high speed) from the ETACS diagno-
sis codes for proper operations(Refer to GROUP
54A, ETACS ).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст