Mitsubishi Outlander (2013+). Manual — part 571
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-43
WINDSHIELD WASHER
REMOVAL AND INSTALLATION
M1511008201626
ACC00346
1,2
3
2
3
4
5
6
A
A
11 ± 2 N·m
AB
Section A – A
Claw
Claw
Rear washer hose
11 ± 2 N·m
1
A
A
Windshield washer nozzle removal
steps
•
Connection of windshield washer
hose
1. Windshield washer nozzle assembly
<LH>
2. Windshield washer nozzle assembly
<RH>
Washer hose removal steps
•
Splash shield (RH) mounting clips
•
Connection of washer nozzle/washer
motor
3. Windshield washer hose
Washer tank removal steps
•
Front bumper assembly (Refer to
•
Engine room side cover (Refer to
)
•
Splash shield (RH) mounting clips
•
Connection of front/rear washer hose
4. Windshield washer tank assembly
5. Windshield washer motor
6. Windshield washer tank
Washer motor removal steps
•
Front bumper assembly (Refer to
•
Connection of front/rear washer hose
5. Windshield washer motor
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-44
INSPECTION
M1511019103685
FRONT WASHER MOTOR INSPECTION
ACB05724 AB
Front
washer
hose
1. The front washer motor must be checked with the
washer tank installed and the washer fluid filled.
2. Connect the battery to the washer motor
connector as shown. Check that the washer motor
delivers washer strongly to the front washer hose
side.
WINDSHIELD WASHER FLUID EJECTION
CHECK
NOTE: Use special tool Adjustment tool, washer
nozzle (MB992326) to adjust the splashing points of
the nozzle.
AC900637
AC
MB992326
Mist type
washer nozzle adjusting side
Jet type washer nozzle
adjusting side
Adjustment of the jet type washer nozzle
injection position
ACC00468 AC
MB992326
Mist type washer
nozzle adjusting side
Mist type
washer nozzle
CAUTION
Adjust the splashing position within the speci-
fied adjustment range, otherwise the windshield
cannot be washed properly.
1. Use special tool Adjustment tool, washer nozzle
(MB992326) to adjust the splashing points of the
nozzle.
2. Insert the jet type washer nozzle adjusting side of
the special tool Adjustment tool, washer nozzle
(MB992326) into the injection part of the washer
nozzle as shown in figure.
3. Move the special tool Adjustment tool, washer
nozzle (MB992326) up and down to adjust the
angle of the washer nozzle as shown in figure.
ACC00351
379
<Left>
<Right>
Unit: mm
Windshield
washer
nozzle
perpendicular
Windshield
washer
nozzle
perpendicular
Ceramic line terminal
434
330
87
39
379
20
175
23
Vehicle centre
line
234
127
234
: Right side washer
: Left side washer
88
38
AB
304
304
Windshield washer
nozzle
23
11
73
39
328
127
23
11
73
330
434
175
23
88
38
WINDSHIELD WIPER AND WASHER
EXTERIOR
51-45
WINDSHIELD WASHER SWITCH CHECK
Check the windshield washer switch from the ETACS
diagnosis codes for proper operation (Refer to
GROUP 54A, ETACS ).
LIGHTING CONTROL SENSOR
LIGHTING CONTROL SENSOR REMOVAL AND INSTALLATION
M1511028300097
For removal and installation, refer to GROUP 54A,
Lighting control sensor .
REAR WIPER AND WASHER
EXTERIOR
51-46
Lighting control sensor (rain sensor)
adaptation
M1511028600139
CAUTION
• Before performing the adaptation, check if the
lighting control sensor (rain sensor)-related
diagnosis code is set. (if set, refer to GROUP
54A, HEADLAMP DIAGNOSIS CODE CHART ).
• Turn the wiper switch to the OFF position.
1. Clean the windshield in fine weather.
2. Wipe the surface of the windshield thoroughly,
and check that the surface is dry.
3. Turn the ignition switch to the ON position.
4. Turn the ignition switch to the LOCK (OFF)
position.
CAUTION
Before connecting or disconnecting M.U.T.-III,
always turn the ignition switch to the LOCK
(OFF) position.
5. Connect the M.U.T.-III to the diagnosis connector.
6. Turn the ignition switch to the ON position.
7. Wipe the windshield surface of the lighting control
sensor section thoroughly, and check that the
surface is dry.
8. Select "LIN" on the "System Select" screen, and
press the "OK" button.
9. Select "Rain light sensor" on the "System Select"
screen, and press the "OK" button.
10.Select "Special Function" on the "Rain light
sensor" screen.
11.Select "Rain Sensor Adaptation" on the "Special
Function" screen.
12.Press the "OK" button, and execute the "Rain
Sensor Adaptation."
13.Press the "OK" button after the execution screen
is displayed.
14.Press the "OK" button after "Completed" is
displayed.
R E A R W I P E R A N D W A S H E R
SERVICE SPECIFICATION
M1511000301544
Item
Standard value
Stop position of rear wiper arm/blade assembly (Distance from the edge of
the wiper blade to the edge of the ceramic line on the tailgate glass) mm
A:
φ 2 marking ± 5
SPECIAL TOOLS
M1511000603284
Tool
Number
Name
Use
MB992326
MB992326
Adjustment tool,
washer nozzle
Injection angle adjustment of the
washer nozzle
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст