Mitsubishi Montero Sport (2004+). Manual — part 497
ON-VEHICLE SERVICE
TSB Revision
INTERIOR
52A-33
PROCESSES FOR ADJUSTING THE COMPASS
VARIANCE
M1524012000053
Under certain circumstances, as during a long distance
cross-country trip, it will be necessary to adjust for compass
variance.
Compass variance is the difference between earth's
magnetic north and true geographic north. If not adjusted to
account for compass variance, your compass could give
false readings.
1. Press the "COMP" button for more than 3 seconds. The
current zone number will appear in the display.
2. Find your current location and variance zone number on the
map given on the left.
3. Press the "COMP" button until the new zone number
appears in the display.
After you stop pressing the button in, the display will show a
compass direction within a few seconds.
NOTE: Do not install the ski rack, antenna, etc. Which are
attached to the vehicle by means of a magnet. They affect
the operation of the compass.
NOTE: If the compass deviates from the correct indication
soon after repeated adjustment, have the compass checked
at an authorized Mitsubishi dealer.
NOTE: The compass may not indicate the correct compass
point in the places shown below:
• Tunnels
• Areas along he railroad
• Underpass
• Transforming station
• Area with many office buildings
• Area over the subway
• Up or down a steep hill
The compass returns to the correct compass point when the
vehicle moves to an area where the geomagnetism in stabi-
lized.
AC003256
AC003257
ON-VEHICLE SERVICE
TSB Revision
INTERIOR
52A-34
AUTO-DIMMING FEATURE TEST
M1524012500058
Be sure the ignition is on and that the mirror is on. The green
LED light to the right of the main display switch will be lit
when the mirror is on. If it's not, depress the "TEMP" side of
the main display switch for 15 seconds.
1. Cover the forward-facing light sensor on the back of the
mirror with a black cloth.
2. While in a well-lit area, make sure light strikes the sensor on
the front of the mirror, simulating glare from vehicles behind
you. The mirror will dim within 2 minutes if the testing for the
first time. If the mirror does not dim, replace the inside rear
view mirror.
AC003258
BLACK CLOSE
LIGHT
TEMP SWITCH
SENSOR
AB
SPECIAL TOOLS
TSB Revision
INTERIOR
52A-35
SPECIAL TOOLS
M1521000600338
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB990784
Ornament remover
General service
tool
Removal of switch, trim,
etc.
MB991958
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991914
F: MB991825
G: MB991826
MUT-III sub assembly
A: Vehicle communication
interface (V.C.I.)
B: MUT-III USB cable
C: MUT-III main harness
A (Vehicles with CAN
communication
system)
D: MUT-III main harness
B (Vehicles without
CAN communication
system)
E: MUT-III main harness
C (for Daimler Chrysler
models only)
F: MUT-III measurement
adapter
G: MUT-III trigger harness
MB991824-KIT
NOTE: G:
MB991826 MUT-III
trigger harness is
not necessary
when pushing
V.C.I. ENTER key.
Reading diagnostic
trouble code
CAUTION
MUT-III main harness B
(MB991911) should be
used. MUT-III main
harness A and C
should not be used for
this vehicle.
MB990784
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
A
B
C
D
E
F
G
DO NOT USE
DO NOT USE
SPECIAL TOOLS
TSB Revision
INTERIOR
52A-36
MB991529
Diagnostic trouble code
check harness
Tool not necessary
if scan tool
(MUT-lll) is
available
ETACS-ECU input signal
checking
(When using the
voltmeter)
MB991223
A: MB991223
Test harness
B: MB991220 LED
harness
C: MB991221 LED
harness adapter
D: MB991222
Probe
MB991223
Measurement of
terminal voltage
A: Connector pin
contact pressure
inspection
B: Power circuit
inspection
C: Power circuit
inspection
D: Commercial tester
connection
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB991529
MB991223
A
B
C
D
AE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст