Mitsubishi Montero Sport (2004+). Manual — part 513

IGNITION SWITCH

TSB Revision

CHASSIS ELECTRICAL

54-39

STEP 10. Check key reminder switch connector D-16 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.

Q: Is the key reminder switch connector D-16 in good

condition?
YES : Go to Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness

Connector Inspection

P.00E-2

STEP 11. Check the harness wire between key reminder
switch connector D-16 (terminal No.4) and body ground.

Q: Is the resistance wire between key reminder switch D-16

and body ground in good condition?
YES : There is no action to be taken.
NO : Repair or replace it. Refer to GROUP 00E, Harness

Connector Inspection

P.00E-2

AC202060

IGNITION SWITCH

TSB Revision

CHASSIS ELECTRICAL

54-40

STEP 12. Check the harness wire between key reminder
switch connector D-16 (terminal No.2 and 6) and
ETACS-ECU connector D-11(terminal No.8 and 12).

NOTE: After checking intermediate connector C-72 and D-13,
check the wires. If intermediate connector C-72 and D-13 are
damaged, repair or replace them. Refer to GROUP 00E, Har-
ness Connector Inspection

P.00E-2

Q: Is the harness wire between key reminder switch D-16

and ETACS-ECU connector D-11 in good condition?
YES : Go to Step 13.
NO : Repair or replace it. Refer to GROUP 00E, Harness

Connector Inspection

P.00E-2

201918

AC201086

AC202060

17 18

10 11 12 13

1
9

AC201910

CONNECTOR: C-72

C-72 (B)

IGNITION SWITCH

TSB Revision

CHASSIS ELECTRICAL

54-41

STEP 13. Check for continuity between terminals (except
No. 4 and No. 6) of key reminder switch connector D-16.

(1) Measure at key reminder switch connector D-16 without

disconnecting the connector.

(2) Check that there is no continuity between key reminder

switch terminal No. 4 and each terminal (except terminal
No. 6), as well as between key reminder switch terminal
No.6 and each terminal (except terminal No. 4).

Q: Does continuity exist between terminals?

YES : Replace the key reminder switch. If the functions,

which are described in "CIRCUIT OPERATION", work
normally, the input signal from the key reminder
switch should be normal.

NO : Go to Step 14.

STEP 14. Recheck for malfunction.
Q: Is a malfunction eliminated?

YES : The procedure is complete. (If no malfunctions are

found in all steps, an intermittent malfunction is
suspected. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Point

P.00-7

NO : Go to Step 1.

AC202060

IGNITION SWITCH

TSB Revision

CHASSIS ELECTRICAL

54-42

EQUIPMENT DIAGNOSIS

IMMOBILIZER SYSTEM DIAGNOSIS

M1543009901393

INTRODUCTION TO IMMOBILIZER
SYSTEM DIAGNOSIS

CAUTION

The encrypted code should always be re-regis-
tered when replacing the immobilizer-ECU.
The immobilizer system consists of the immobi-
lizer-ECU, powertrain control module, ignition key
and ignition key ring antenna. If the engine cannot be
started by using a registered ignition key, one of
these components may be defective. In addition, if

the immobilizer system has immobilized the engine,
MFI system DTC P1610 will be output. In this case,
observe the immobilizer system troubleshooting.
Then, if a malfunction is resolved, the MFI system
DTC P1610 should not reset.

IMMOBILIZER SYSTEM DIAGNOSTIC TROUBLESHOOTING STRATEGY

M1543006900711

Use these steps to plan your diagnostic strategy. If
you follow them carefully, you will be sure that you
have exhausted most of the possible ways to find an
immobilizer system fault.
1. Gather information about the problem from the

customer.

2. Verify that the condition described by the

customer exists.

3. Check the vehicle for any immobilizer system

DTC.

4. If you cannot verify the condition and there are no

immobilizer system DTCs, the malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/inspection Service Points - How
to Cope with Intermittent Malfunctions

P.00-7

5. If you can verify the condition but there are no

immobilizer system DTCs, or the system cannot
communicate with scan tool MB991958, refer to
Symptom Chart and find the fault

P.54-48

6. If there is an immobilizer system DTC, record the

number of the DTC, then erase the DTC from the
memory using scan tool MBB991958.

7. Recreate the immobilizer system DTC set

conditions to see if the same immobilizer system
DTC will set again.
(1) If the same immobilize system DTC sets

again, perform the diagnostic procedures for
the DTC. Refer to Diagnostic Trouble Code
Chart

P.54-43

(2) If you cannot get the same immobilizer system

DTC to set again, the malfunction is
intermittent. Refer to GROUP 00, How to Use
Troubleshooting/inspection Service Points