Mitsubishi Montero Sport (2004+). Manual — part 525
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54-87
NOTE: After checking intermediate connector C-29, check the
wires. If intermediate connector C-29 is damaged, repair or
replace it. Refer to GROUP 00E, Harness Connector Inspec-
tion
.
Q: Are the harness wires between combination meter
connector C-02 and vehicle speed sensor connector
B-09 in good condition?
YES : There is no action to be taken.
NO : Repair them. The speedometer should work normally.
STEP 15. Measure the voltage at the vehicle speed sensor
power supply circuit.
(1) Disconnect the vehicle speed sensor connector B-09.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 1 and ground.
• The measured value should be approximately 12 volts
(battery positive voltage).
Q: Does the measured voltage correspond with this range?
YES : Go to Step 18.
NO : Go to Step 16.
AC201842
9
3
8
6 7
5
4
1 2
AB
CONNECTOR: C-29
C-29
AC003458 AC
CONNECTOR: B-09
<RWD>
B-09 (B)
1
2
3
B-09: HARNESS
SIDE CONNECTOR
AC201841
3 2 1
CONNECTOR: B-09
AB
B-09: HARNESS
SIDE CONNECTOR
<4WD>
B-09 (B)
ACX01755
B-09 HARNESS CONNECTOR:
COMPONENT SIDE
AD
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54-88
STEP 16. Check vehicle speed sensor connector B-09 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is vehicle speed sensor connector B-09 in good
condition?
YES : Go to Step 17.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. The speedometer
should work normally.
STEP 17. Check the harness wires between vehicle speed
sensor connector B-09 (terminal No.1) and ignition switch
(IG1).
AC003458 AC
CONNECTOR: B-09
<RWD>
B-09 (B)
1
2
3
B-09: HARNESS
SIDE CONNECTOR
AC201841
3 2 1
CONNECTOR: B-09
AB
B-09: HARNESS
SIDE CONNECTOR
<4WD>
B-09 (B)
AC003458 AC
CONNECTOR: B-09
<RWD>
B-09 (B)
1
2
3
B-09: HARNESS
SIDE CONNECTOR
AC201841
3 2 1
CONNECTOR: B-09
AB
B-09: HARNESS
SIDE CONNECTOR
<4WD>
B-09 (B)
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54-89
NOTE: After checking junction block connectors D-06 and
D-08, check the wires. If junction block connectors D-06 and
D-08 are damaged, repair or replace them. Refer to GROUP
00E, Harness Connector Inspection
Q: Are the harness wires between vehicle speed sensor
connector B-09 (terminal No.1) and ignition switch (IG1)
in good condition?
YES : There is no action to be taken.
NO : Repair them. The speedometer should work normally.
AC200772
1
8
3
4
5
7 6
10
15
16
14
12
13
11
9
2
COMPONENT SIDE
CONNECTOR: D-06
D-06
JUNCTION BLOCK
(FRONT)
AB
AC200773
M
3
1
4
2
CONNECTOR: D-08
D-08
COMPONENT SIDE
AB
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54-90
STEP 18. Check the resistance at the vehicle speed sensor
ground circuit.
(1) Disconnect the vehicle speed sensor connector B-09.
(2) Measure the resistance between terminal 2 and ground.
• The measured value should be 2 ohms or less.
Q: Does the measured resistance value correspond with
this range?
YES : Go to Step 21.
NO : Go to Step 19.
AC003458 AC
CONNECTOR: B-09
<RWD>
B-09 (B)
1
2
3
B-09: HARNESS
SIDE CONNECTOR
AC201841
3 2 1
CONNECTOR: B-09
AB
B-09: HARNESS
SIDE CONNECTOR
<4WD>
B-09 (B)
ACX01756AE
B-09 HARNESS CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст