Mitsubishi Montero Sport (2004+). Manual — part 524
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54-83
STEP 10. Check combination meter connector C-02 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is combination meter connector C-02 in good
condition?
YES : Go to Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. The speedometer
should work normally.
STEP 11. Check the harness wires between combination
meter connector C-02 (terminal No.53) and fusible link
number 8.
AC201839
CONNECTOR: C-02
AC
51
52
55 54 53
56
58
59
57
60
61
62
COMPONENT SIDE
C-02 (B)
AC201839
CONNECTOR: C-02
AC
51
52
55 54 53
56
58
59
57
60
61
62
COMPONENT SIDE
C-02 (B)
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54-84
NOTE: After checking junction block connectors D-01 and D-06
and IOD or storage connector A-54X, check the wires. If junc-
tion block connectors D-01 and D-06 and IOD or storage con-
nector A-54X are damaged, repair or replace them. Refer to
GROUP 00E, Harness Connector Inspection
Q: Are the harness wires between combination meter
connector C-02 (terminal No.53) and fusible link number
8?
YES : There is no action to be taken.
NO : Repair them. The speedometer should work normally.
AC201809
2
3
4
11 10 9 8 7
1
6
5
12
1
8
3
4
5
7 6
10
15
16
14
12
13
11
9
2
D-01 COMPONENT SIDE
D-06 COMPONENT SIDE
AB
D-01
D-06
JUNCTION BLOCK (FRONT)
CONNECTORS: D-01, D-06
AC200774
2
1
CONNECTOR: A-54X
AB
A-54X
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54-85
STEP 12. Check the combination meter vehicle speed
sensor input signal circuit at combination meter connector
C-02.
(1) Do not disconnect vehicle speed sensor connector B-09.
(2) Disconnect combination meter connector C-02.
(3) Turn the ignition switch to the "ON" position.
(4) Measure the voltage between terminal 51 and ground.
• The measured value should be approximately 5 volts.
Q: Does the measured voltage correspond with this range?
YES : Repair or replace the combination meter
(printed-circuit board or speedometer and
tachometer). The speedometer should work normally.
NO : Go to Step 13.
AC003458 AC
CONNECTOR: B-09
<RWD>
B-09 (B)
1
2
3
B-09: HARNESS
SIDE CONNECTOR
AC201841
3 2 1
CONNECTOR: B-09
AB
B-09: HARNESS
SIDE CONNECTOR
<4WD>
B-09 (B)
AC201839
CONNECTOR: C-02
AC
51
52
55 54 53
56
58
59
57
60
61
62
COMPONENT SIDE
C-02 (B)
AC003649AB
CONNECTOR C-02
(HARNESS SIDE)
COMBINATION METER ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54-86
STEP 13. Check combination meter connector C-02 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is combination meter connector C-02 in good
condition?
YES : Go to Step 14.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. The speedometer
should work normally.
STEP 14. Check the harness wires between combination
meter connector C-02 and vehicle speed sensor connector
B-09.
AC201839
CONNECTOR: C-02
AC
51
52
55 54 53
56
58
59
57
60
61
62
COMPONENT SIDE
C-02 (B)
AC201839
CONNECTOR: C-02
AC
51
52
55 54 53
56
58
59
57
60
61
62
COMPONENT SIDE
C-02 (B)
AC003458 AC
CONNECTOR: B-09
<RWD>
B-09 (B)
1
2
3
B-09: HARNESS
SIDE CONNECTOR
AC201841
3 2 1
CONNECTOR: B-09
AB
B-09: HARNESS
SIDE CONNECTOR
<4WD>
B-09 (B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст