Mitsubishi Montero Sport (2004+). Manual — part 507
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54-15
STEP 5. Check driver's side door switch connector E-33
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is driver's side door switch connector E-33 damaged?
YES : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. The tachometer
should work normally.
NO : Go to Step 6.
STEP 6. Check the driver's side door switch connector
E-33.
(1) Disconnect the driver's side door switch connector E-33 and
the harness side.
(2) Measure the voltage between terminal 2 and ground.
• The measured value should be approximately 5 volts.
Q: Does the measured voltage correspond with this range?
YES : There is no action to be taken.
NO : Go to Step 7.
AC202056
2 1
COMPONENT SIDE
CONNECTOR: E-33
AB
E-33
AC202056
2 1
COMPONENT SIDE
CONNECTOR: E-33
AB
E-33
AC002735
E-33 HARNESS CONNECTOR:
COMPONENT SIDE
AC
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54-16
STEP 7. Check the harness wires between driver's side
door switch connector E-33 (terminal No.2) and ETACS
connector D-11 (terminal No.9).
AC201939
1
3
4
7 6 5
2
9
11
12
10
13
8
1
8
3
4
5
7 6
10
15
16
14
12
13
11
9
2
CONNECTORS: D-11, D-14
D-11
D-14 (B)
D-11 COMPONENT SIDE
D-14 COMPONENT SIDE
AB
JUNCTION BLOCK
(FRONT)
AC201940
2 1
8
19
7
6
5
16
15
17 18
4
3
2
10 11 12 13
1
9
14
CONNECTORS: E-33, E-42
AC
E-33 (B)
E-42
COMPONENT SIDE
E-42
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54-17
NOTE: After inspecting junction block connector D-14 and
intermediate connector E-42, inspect the wire. If junction block
connector D-14 and intermediate connector E-42 are dam-
aged, repair or replace them. Refer to GROUP 00E, Harness
Connector Inspection
.
Q: Are the harness wires between driver's side door switch
connector E-33 (terminal No.2) and ETACS connector
D-11 (terminal No.9) in good condition?
YES : Go to Step 8.
NO : Repair them. Then check that the malfunction is
eliminated.
STEP 8. Check the ignition key hole illumination light
input.
(1) Remove the driver's under cover (Refer to
(2) Remove the lower and upper column covers (Refer to
).
(3) Disconnect wiring connector D-16 from the key reminder
switch and measure at the switch side.
(4) Connect a vehicle battery as shown, and then check the
ignition key hole illumination light illuminates.
Q: Does the situation key hole illumination light
illuminate?
YES : Go to Step 9.
NO : Replace the key reminder switch.
AC202060
4
5
3
1
6
7
2
1
3
2
7
6
5
4
+
-
AC102749
CONNECTOR: D-16
AB
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54-18
STEP 9. Check the power supply for the ignition key hole
illumination light.
(1) Disconnect the key reminder switch connector D-16 and
measure at the harness side.
(2) Measure the voltage between terminal 1 and ground.
• The measured value should be approximately 12 volts
(battery positive voltage).
Q: Is the measured voltage within this specified range?
YES : Go to Step 11.
NO : Go to Step 10.
STEP 10. Check connector D-16 at the key reminder switch
for damage.
Q: Is key reminder switch connector D-16 in good
condition?
YES : Go to Step 11.
NO : Replace it. Then check that the malfunction is
eliminated.
STEP 11. Check the harness wires between fusible link
number 8 and key reminder switch connector D-16
(terminal No.1).
AC202060
4
5
3
1
6
7
2
AC309477
D-16 HARNESS CONNECTOR:
COMPONENT SIDE
AB
AC202060
4
5
3
1
6
7
2
AC202060
4
5
3
1
6
7
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст