Mitsubishi Montero Sport (2004+). Manual — part 238
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-365
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-II Drive Cycle −
Procedure 6
− Other Monitor
.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
• Open or shorted left bank heated oxygen sensor
(rear) heater circuit, or harness damage.
• Open circuit in left bank heated oxygen sensor
(rear) heater.
• Left bank heated oxygen sensor (rear) failed.
• Connector damage.
• PCM failed.
DIAGNOSIS
Required Special Tool:
• MD998464: Test Harness Set
STEP 1. Check connector E-48 at the left bank heated
oxygen sensor (rear) for damage.
Q: Is the connector in good condition?
YES : Go to Step 2.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
AK200498
1
2
3
4
E-48(B)
AB
CONNECTOR: E-48
HARNESS
CONNECTOR:
COMPONENT SIDE
LEFT BANK
HEATED OXYGEN
SENSOR (REAR)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-366
STEP 2. Check the left bank heated oxygen sensor (rear).
(1) Disconnect left bank heated oxygen sensor (rear) connector
E-48 and connect test harness special tool, MD998464, to
the connector on the left bank heated oxygen (rear) sensor
side.
(2) Measure the resistance between heated oxygen sensor
connector terminal No. 1 (red clip) and terminal No. 3 (blue
clip).
Standard value: 11
− 18 ohms [at 20°C (68°F)]
Q: Is the measured resistance between 11 and 18 ohms [at
20
°C (68°F)]?
YES : Go to Step 3.
NO : Replace the left bank heated oxygen sensor (rear).
Then go to Step 12.
AK200498
1
2
3
4
E-48(B)
AB
CONNECTOR: E-48
HARNESS
CONNECTOR:
COMPONENT SIDE
LEFT BANK
HEATED OXYGEN
SENSOR (REAR)
AKX01624
HEATED
OXYGEN
SENSOR
EQUIPMENT
SIDE
CONNECTOR
MD998464
BLUE
RED
AC
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-367
STEP 3. Measure the power supply voltage at left bank
heated oxygen sensor (rear) harness side connector E-48.
(1) Disconnect the connector E-48 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 1 and ground.
• Voltage should be battery positive voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 5.
NO : Go to Step 4.
STEP 4. Check connector C-59 at the MFI relay for damage.
Q: Is the connector in good condition?
YES : Check connector C-14, C-79 and E-45 at
intermediate connector for damage, and repair or
replace as required. Refer to GROUP 00E, Harness
Connector Inspection
. If intermediate
connector is in good condition, repair harness wire
between MFI relay connector C-59 (terminal No. 1)
and left bank heated oxygen sensor (rear) connector
E-48 (terminal No.1) because of open circuit or short
circuit to ground. Then go to Step 12.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
AK200498
1
2
3
4
E-48(B)
AB
CONNECTOR: E-48
HARNESS
CONNECTOR:
COMPONENT SIDE
LEFT BANK
HEATED OXYGEN
SENSOR (REAR)
AKX01498 BD
2
1
4
3
E-48 HARNESS
CONNECTOR:
COMPONENT SIDE
AK200023
2 1
3
4
CONNECTOR: C-59
AB
C-59
HARNESS
CONNECTOR:
COMPONENT
SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-368
STEP 5. Measure the power supply voltage at PCM
connector C-89 by backprobing.
(1) Do not disconnect the connector 89.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 26 and ground
by backprobing.
• Voltage should be battery positive voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 8.
NO : Go to Step 6.
STEP 6. Check connector C-89 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 7.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
AK103914
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
30
21
22
23
24
25
26
27
28
29
31
32
33
34
35
1
10
AB
CONNECTOR: C-89
C-89(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AKX01543
AKX01543
1
2
3 4
5 6
7 8
10 11 12 13 14 15 16 17 18 19 20 21 22 23
24 25
26 27 28 29
30 31 32 33
34 35
C-89 HARNESS CONNECTOR:
HARNESS SIDE
AH
9
AK103914
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
30
21
22
23
24
25
26
27
28
29
31
32
33
34
35
1
10
AB
CONNECTOR: C-89
C-89(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст