Mitsubishi Montero Sport (2004+). Manual — part 817
SPECIAL TOOLS
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS) <4WD>
35C-75
SPECIAL TOOLS
M1352000600750
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB991958
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991914
F: MB991825
G: MB991826
MUT-III sub assembly
A: Vehicle
communication
interface (V.C.I.)
B: MUT-III USB cable
C: MUT-III main harness
A (Vehicles with CAN
communication
system)
D: MUT-III main harness
B (Vehicles without
CAN communication
system)
E: MUT-III main harness
C (for Daimler Chrysler
models only)
F: MUT-III measurement
adapter
G: MUT-III trigger
harness
MB991824-KIT
NOTE: G: MB991826
MUT-III trigger harness is
not necessary when
pushing V.C.I. ENTER
key.
Checking for ABS system
CAUTION
MUT-III main harness B
(MB991911) should be
used. MUT-III main
harness A and C should
not be used for this
vehicle.
MB991348
The harness set
−
For checking of G-sensor
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
DO NOT USE
A
B
C
D
E
F
G
DO NOT USE
MB991348
ON-VEHICLE SERVICE
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS) <4WD>
35C-76
ON-VEHICLE SERVICE
BLEEDING
M1352001500284
Refer to GROUP 35B, On-vehicle Service
WHEEL SPEED SENSOR OUTPUT VOLTAGE
MEASUREMENT
M1352001600559
Refer to GROUP 35B, On-vehicle Service
HYDRAULIC UNIT CHECK
M1352001700619
Refer to GROUP 35B, On-vehicle Service
ABS RELAY CHECK
M1352011000149
Refer to GROUP 35B, On-vehicle Service
DISCHARGED BATTERY
M1352003500570
Refer to GROUP 35B, On-vehicle Service
MASTER CYLINDER AND BRAKE BOOSTER
REMOVAL AND INSTALLATION
M1352004000211
Refer to GROUP 35A, Master Cylinder and Brake
Booster
MASTER CYLINDER DISASSEMBLY AND ASSEMBLY
M1352004500216
Refer to GROUP 35B, Master Cylinder and Brake
Booster
INSPECTION
M1352004100070
Refer to GROUP 35B, Master Cylinder and Brake Booster
.
HYDRAULIC UNIT
REMOVAL AND INSTALLATION
M1352008600505
Refer to GROUP 35B, Hydraulic Unit
WHEEL SPEED SENSOR
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS) <4WD>
35C-77
WHEEL SPEED SENSOR
REMOVAL AND INSTALLATION
M1352008300582
Refer to GROUP 35B, Wheel Speed Sensor
.
INSPECTION
M1352008400482
Refer to GROUP 35B, Wheel Speed Sensor
G-SENSOR
REMOVAL AND INSTALLATION
M1352010100295
CAUTION
Do not drop or apply a shock on the G-sensor.
G-SENSOR CHECK
M1352010200098
Required Special Tool:
• MB991348: Test Harness Set
1. Disconnect the G-sensor connector and connect special tool
MB991348, between terminals of the disconnected
connector.
2. With the ignition switch turned to the "ON" position, read the
voltage between terminals number 2 and number 3.
Standard Value: 2.4
− 2.6 V
3. With special tool MB991348 connected, rotate so that the
arrow faces straight down. Read output voltage between
terminals number 2 and number 3.
Standard Value: 3.4
− 3.6 V
4. If the voltage deviates from the standard value, make sure
that nothing is wrong with the power supply wire and ground
wire and then replace the G-sensor.
Pre-removal and Post-installation Operation
• Front and Rear Console Assembly Removal and Installa-
tion (Refer to GROUP 52A, Floor Console
AC004987
G-SENSOR
AB
AC004984
MB991348
AB
SPECIFICATIONS
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS) <4WD>
35C-78
SPECIFICATIONS
SERVICE SPECIFICATION
M1352000300630
For the service specifications of the wheel speed sensor, refer to GROUP 35B, Service Specification
.
ITEM
STANDARD VALUE
G-sensor output voltage V
Stationary vehicles
2.4
− 2.6
Arrow facing downward
3.4
− 3.6
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст