Mitsubishi Montero Sport (2004+). Manual — part 818
36-1
GROUP 36
PARKING BRAKES
CONTENTS
GENERAL INFORMATION . . . . . . . .
ON-VEHICLE SERVICE. . . . . . . . . . .
PARKING BRAKE LEVER STROKE
CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PARKING BRAKE SWITCH CHECK . . . . .
PARKING BRAKE LEVER . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
PARKING BRAKE CABLE. . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
SPECIFICATIONS . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS . . . . . . . . . . .
GENERAL INFORMATION
TSB Revision
PARKING BRAKES
36-2
GENERAL INFORMATION
M1361000100366
The parking brake is lever type of an mechanical
rear-wheel brake construction in all vehicles.
CONSTRUCTION DIAGRAM
ON-VEHICLE SERVICE
PARKING BRAKE LEVER STROKE CHECK
M1361000900395
CAUTION
The 196 N (44 pounds) force of he parking brake lever must
be strictly observed.
1. Pull the parking brake lever with a force of approximately
196 N (44 pounds) and count the number of notches.
Standard value: 6
− 7 notches
2. Lever Stroke Adjustment
Remove the switch panel (Refer to GROUP 52A, Floor
Console
.) then loosen the adjusting nut as far as
the end of the cable rod as shown in the illustration. Then
release the parking brake cable to adjust the parking brake
lever stroke by the following procedures.
3. With the engine idling, depress the brake pedal five or six
times fully and confirm that the pedal stroke does not
change.
NOTE: If the pedal stroke does not change, the auto-
matic-adjusting mechanism is functioning normally, and
clearance between the shoe and drum is correct.
AC004551
AC004552
ADJUSTING NUT
AB
ON-VEHICLE SERVICE
TSB Revision
PARKING BRAKES
36-3
CAUTION
If the number of the brake lever notches engaged is less
than the standard value, the cable has been pulled exces-
sively. Be sure to adjust it to the standard value.
4. Turn the adjusting nut to adjust the parking brake lever
stroke to within the standard value range.
5. Check that there is no play between the adjusting nut and
the parking brake lever.
6. Release the parking brake lever, and jack up the rear of the
vehicle.
7. Turn the rear wheel to confirm that the rear brakes are not
dragging.
PARKING BRAKE SWITCH CHECK
M1361003300444
1. Remove the rear floor console assembly. (Refer to GROUP
52A, Floor Console
2. Disconnect the connector of the parking brake switch, and
connect an ohmmeter between the parking brake switch and
the switch installation bolt.
3. The parking brake switch is good if there is continuity when
the parking brake lever or parking brake pull rod is pulled,
and there is no continuity when it is released.
AC004553
PARKING BRAKE LEVER
TSB Revision
PARKING BRAKES
36-4
PARKING BRAKE LEVER
REMOVAL AND INSTALLATION
M1361001300385
Pre-removal Operation
• Rear Floor Console Removal (Refer to GROUP 52A,
Floor Console
Post-installation Operation
• Parking Brake Lever Stroke Adjustment (Refer to
• Rear Floor Console Installation (Refer to GROUP 52A,
AC004556AB
3
4
5
6
1
2
6
A
A
SECTION A - A
REMOVAL
STEPS
1.
PARKING BRAKE LEVER
CONNECTION
2.
PARKING BRAKE SWITCH
3.
BRACKET <VEHICLES WITH REAR
HEATER>
4.
PARKING BRAKE LEVER STAY
5.
PARKING BRAKE LEVER BUSHING
6.
PARKING BRAKE LEVER
REMOVAL
STEPS
(Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст