Mitsubishi Montero Sport (2004+). Manual — part 761
ON-VEHICLE SERVICE
TSB Revision
WHEEL AND TIRE
31-7
ON-VEHICLE SERVICE
TIRE INFLATION PRESSURE CHECK
M1311000900378
NOTE: For information on tire inflation pressure, refer to the
label attached to the center pillar at the driver's side.
TIRE WEAR CHECK
M1311001000390
Measure the tread depth of the tires.
Minimum limit: 1.6 mm (0.06 inch)
If the remaining tread depth is less than the minimum limit,
replace the tire.
NOTE: When the tread depth of the tires is reduced to 1.6 mm
(0.06 inch) or less, wear indicators will appear.
WHEEL RUNOUT CHECK
M1311001100416
Jack up the vehicle so that the wheels are clear of the floor.
While slowly turning the wheel, measure wheel runout with a
dial indicator.
Limit:
Radial runout: 1.0 mm (0.04 inch) or less
Lateral runout: 1.0 mm (0.04 inch) or less
If wheel runout exceeds the limit, replace the wheel.
ACX00651AB
LATERAL
RADIAL
SPECIFICATIONS
TSB Revision
WHEEL AND TIRE
31-8
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATION
M1311001600336
GENERAL SPECIFICATIONS
M1311000200379
NOTE: PCD indicates the pitch circle diameter of the wheel installation holes.
SERVICE SPECIFICATIONS
M1311000300451
ITEM
SPECIFICATION
Wheel nut
98
− 120 N⋅m (72 − 87 ft-lb)
ITEM
SPECIFICATION
Wheel (including spare
wheel)
Type
Road wheel
Aluminum type
Spare wheel
Steel type
Size
16
× 7JJ
Amount of wheel offset mm
(in)
10 (0.4)
Pitch circle diameter (PCD)
mm (in)
139.7 (5.50)
Tire (including spare tire) Size
P255/70 R16 109S
ITEM
LIMIT
Tire radial-force variation N (pound)
Maximum 98 (21.9)
Tread depth of tire mm (in)
Minimum 1.6 (0.06)
Wheel runout (Radial runout) mm (in)
1.0 (0.04) or less
Wheel runout (Lateral runout) mm (in)
1.0 (0.04) or less
33A-1
GROUP 33A
FRONT
SUSPENSION
CONTENTS
GENERAL DESCRIPTION. . . . . . . . .
SPECIAL TOOLS. . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE. . . . . . . . . . .
FRONT WHEEL ALIGNMENT CHECK AND
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . .
BALL JOINT DUST COVER CHECK . . . . .
SHOCK ABSORBER ASSEMBLY AND
UPPER ARM . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION . . . . . . . . . . . . . . . . . . . . . . .
BALL JOINT DUST COVER
REPLACEMENT . . . . . . . . . . . . . . . . . . . . .
LOWER ARM AND TORSION BAR .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
REAR LOWER ARM BUSHING
REPLACEMENT . . . . . . . . . . . . . . . . . . . . .
FRONT LOWER ARM BUSHING
REPLACEMENT . . . . . . . . . . . . . . . . . . . . .
LOWER ARM BALL JOINT DUST COVER
REPLACEMENT . . . . . . . . . . . . . . . . . . . . .
STABILIZER BAR. . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
SPECIFICATIONS . . . . . . . . . . . . . . .
FASTENER TIGHTENING
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . .
GENERAL SPECIFICATIONS . . . . . . . . . .
SERVICE SPECIFICATIONS . . . . . . . . . . .
SEALANTS AND ADHESIVES . . . . . . . . . .
GENERAL DESCRIPTION
TSB Revision
FRONT SUSPENSION
33A-2
GENERAL DESCRIPTION
M1331000100095
Front suspension is an independent suspension hav-
ing the double wishbone combined with the torsion
bar spring.
SPECIAL TOOLS
M1331000600090
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB991897
Ball joint remover
MB991113-01,
MB990635-01 or General
service tool
Ball joint removal
NOTE: Steering linkage
puller (MB990635 or
MB991113) is also used
to disconnect knuckle and
tie rod end ball joint.
MB990326
Preload socket
General service tool
Ball joint rotating torque
check
MB991522
Torsion bar bushing
remover and installer
−
Removal and press-fitting
of bushing
MB990883
Arbor
MB990883-01
Removal and press-fitting
of lower arm bushing
MB990957
Lower arm bushing
remover and installer
A: MB990971
Base
Tool not available
AC106827
MB990326
MB991522
MB990883
MB990957
A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст