Mitsubishi Montero Sport (2004+). Manual — part 265
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-473
STEP 3. Retest the system.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
Other Monitor
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0340 set?
YES : Replace the PCM. Then go to Step 18.
NO : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
STEP 4. Check connector A-42 at camshaft position
sensor for damage.
Q: Is the connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 18.
AK200488
1
2
3
AB
CONNECTOR: A-42
A-42(GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
CAMSHAFT
POSITION
SENSOR
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-474
STEP 5. Measure the sensor supply voltage at camshaft
position sensor connector A-42.
(1) Disconnect the connector A-42 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 2 and ground.
• Voltage should be between 4.8 and 5.2 volts
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.8 and 5.2 volts?
YES : Go to Step 10.
NO : Go to Step 6.
AK200488
1
2
3
AB
CONNECTOR: A-42
A-42(GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
CAMSHAFT
POSITION
SENSOR
AK000010
A-42 HARNESS
CONNECTOR:
COMPONENT SIDE
3 2 1
AF
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-475
STEP 6. Measure the sensor supply voltage at PCM
connector C-90 by backprobing.
(1) Do not disconnect the PCM connector C-90.
(2) Disconnect the camshaft position sensor connector A-42.
(3) Turn the ignition switch to the "ON" position.
(4) Measure the voltage between terminal No. 56 and ground
by backprobing.
• Voltage should be between 4.8 and 5.2 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.8 and 5.2 volts?
YES : Go to Step 7.
NO : Go to Step 8.
STEP 7. Check connector C-90 at PCM for damage.
Q: Is the connector in good condition?
YES : Repair harness wire between camshaft position
sensor connector A-42 (terminal No. 2) and PCM
connector C-90 (terminal No. 56) because of open
circuit. Then go to Step 18.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 18.
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AKX01545
41
AG
C-90 HARNESS CONNECTOR:
HARNESS SIDE
42 43
44 45 46
47 48 49 50 51 52 53 54 55 56 57
58 59
60 61 62 63
64
66
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-476
STEP 8. Check connector C-90 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 9.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 18.
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст