Mitsubishi Montero Sport (2004+). Manual — part 263
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-465
STEP 15. Check connector C-90 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 16.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 20.
STEP 16. Check for harness damage between MFI relay
connector C-59 (terminal No. 1) and crankshaft position
sensor connector A-43 (terminal No. 3).
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AK200494
1
2
3
A-43(B)
AB
CONNECTOR: A-43
HARNESS
CONNECTOR:
COMPONENT SIDE
CRANKSHAFT
POSITION
SENSOR
AK200023
2 1
3
4
CONNECTOR: C-59
AB
C-59
HARNESS
CONNECTOR:
COMPONENT
SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-466
NOTE: Check harness after checking intermediate connector
C-14. If intermediate connector is damaged, repair or replace it.
Refer to GROUP 00E, Harness Connector Inspection
Then go to Step 20.
Q: Is the harness wire in good condition?
YES : Go to Step 17.
NO : Repair it. Then go to Step 20.
STEP 17. Check for harness damage between crankshaft
position sensor connector A-43 (terminal No. 2) and PCM
connector C-90 (terminal No. 45).
Q: Is the harness wire in good condition?
YES : Go to Step 18.
NO : Repair it. Then go to Step 20.
AK200494
1
2
3
A-43(B)
AB
CONNECTOR: A-43
HARNESS
CONNECTOR:
COMPONENT SIDE
CRANKSHAFT
POSITION
SENSOR
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-467
STEP 18. Check for harness damage between crankshaft
position sensor connector A-43 (terminal No. 1) and
ground.
Q: Is the harness wire in good condition?
YES : Go to Step 19.
NO : Repair it. Then go to Step 20.
STEP 19. Check the crankshaft sensing blade.
Q: Is the crankshaft sensing blade in a good condition?
YES : Replace the crankshaft position sensor. Then go to
Step 20.
NO : Peplace the crankshaft sensing blade. Then go to
Step 20.
STEP 20. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
Other Monitor
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0335 set?
YES : Repeat the troubleshooting.
NO : The procedure is complete.
AK200494
1
2
3
A-43(B)
AB
CONNECTOR: A-43
HARNESS
CONNECTOR:
COMPONENT SIDE
CRANKSHAFT
POSITION
SENSOR
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-468
DTC P0340: Camshaft Position Sensor Circuit
AK200189
Camshaft Position Sensor Circuit
WHITE-
BLA
CK
WHITE-
BLA
CK
WHITE-
BLA
CK
BLA
CK
RED
RED
BLUE-
WHITE
FUSIBLE LINK(12)
MFI
RELAY
56
3
12
3
4
2
1
16
1
2
A-42
MU802663
5V
POWERTRAIN CONTROL
MODULE (PCM)
CAMSHAFT
POSITION
SENSOR
C-59
1
10
2 3 4 5 6 7 8 9
11
12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33
C-14
47
41
42 43
48 49 50 51 52 53 54 55 56 57
46
45
44
58
59
60 61 62 63
64 65 66
C-90
(MU803781)
3
1 2
JOINT
CONNECTOR (5)
1
2
3
4
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст