Mitsubishi Montero Sport (2004+). Manual — part 171
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-97
DTC P0112: Intake air temperature Circuit Low Input
AK301863
Intake Air Temperature Sensor Circuit
RED
-BL
UE
BL
ACK
BL
ACK
57
5
5V
POWERTRAIN CONTROL MODULE (PCM)
INTAKE AIR TEMPERATURE SENSOR
(INCORPORATED IN VOLUME
AIRFLOW SENSOR)
12
6
64
15
1 2 3 4 5 6 7
A-01
1
10
2 3 4 5 6 7 8 9
11
12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33
C-71
47
41
42 43
48 49 50 51 52 53 54 55 56 57
46
45
44
58
59
60 61 62 63
64 65 66
C-90
(MU803781)
JOINT
CONNEC-
TOR (4)
AK103908
CONNECTOR: A-01
INTAKE AIR
TEMPERATURE
SENSOR
A-01(B)
AD
AK103738AC
CONNECTOR: C-90
PCM
C-90(GR)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-98
.
CIRCUIT OPERATION
• Approximately 5 volts are applied to the intake air
temperature sensor output terminal (terminal No.
6) from the PCM (terminal No. 64) via the resistor
in the PCM. The ground terminal (terminal No. 5)
is grounded with PCM (terminal No. 57).
• The intake air temperature sensor is a negative
temperature coefficient type of resistor. When the
intake air temperature rises, the resistance
decreases.
• The intake air temperature sensor output voltage
increases when the resistance increases and
decreases when the resistance decreases.
.
TECHNICAL DESCRIPTION
• The intake air temperature sensor converts the
intake air temperature to a voltage.
• The PCM checks whether this voltage is within a
specified range.
.
DESCRIPTIONS OF MONITOR METHODS
Intake air temperature sensor output voltage is out of
specified range.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Not applicable
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
AK103912AB
CONNECTOR: C-71
C-71
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-99
DTC SET CONDITIONS
Logic Flow Chart
.
Check Conditions
• 2 seconds or more have passed since the start-
ing sequence was completed.
Judgement Criteria
• Intake air temperature sensor output voltage has
continued to be0.2 volt or lower [corresponding to
an air intake temperature of 115
°C (239°F) or
higher] for 2 seconds.
.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-II Drive Cycle −
Procedure 6
.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
• Intake air temperature sensor failed.
• Shorted intake air temperature sensor circuit, or
connector damage.
• PCM failed.
START
OUTPUT VOLTAGE < 0.2V
END
NO
NO
NO
YES
YES
YES
MALFUNCTION
GOOD
CONTINUOUS
FAILURE FOR 2secs
OUTPUT VOLTAGE > 4.6V
MONITORING
CONDITIONS
NO
YES
AK301424
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-100
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I
• MB991827: USB Cable
• MB991911: Main Harness B
STEP 1. Using scan tool MB991958, check data list item 13:
Intake Air Temperature Sensor.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to the data reading mode for item
13, Intake Air Temperature Sensor.
• The intake air temperature and temperature shown with
the scan tool should approximately match.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
NO : Go to Step 2.
STEP 2. Check connector A-01 at the intake air
temperature sensor for damage.
Q: Is the connector in good condition?
YES : Go to Step 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 6.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
AK103913
3
4
5
1
2
6
7
CONNECTOR: A-01
A-01(B)
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст