Mitsubishi Montero Sport (2004+). Manual — part 262
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-461
STEP 9. Check connector C-90 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 10.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 20.
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-462
STEP 10. Check for short circuit to ground between
crankshaft position sensor connector A-43 (terminal No. 2)
and PCM connector C-90 (terminal No. 45).
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 20.
NO : Repair it. Then go to Step 20.
AK200494
1
2
3
A-43(B)
AB
CONNECTOR: A-43
HARNESS
CONNECTOR:
COMPONENT SIDE
CRANKSHAFT
POSITION
SENSOR
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-463
STEP 11. Measure the power supply voltage at crankshaft
position sensor harness side connector A-43.
(1) Disconnect the connector A-43 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 3 and ground.
• Voltage should be battery positive voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 13.
NO : Go to Step 12.
STEP 12. Check connector C-59 at MFI relay for damage.
Q: Is the connector in good condition?
YES : Check connector C-14 at intermediate connector for
damage, and repair or replace as required. Refer to
GROUP 00E, Harness Connector Inspection
. If intermediate connector is in good
condition, repair harness wire between MFI relay
connector C-59 (terminal No. 1) and crankshaft
position sensor connector A-43 (terminal No. 3)
because of open circuit or short circuit to ground.
Then go to Step 20.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 20.
AK200494
1
2
3
A-43(B)
AB
CONNECTOR: A-43
HARNESS
CONNECTOR:
COMPONENT SIDE
CRANKSHAFT
POSITION
SENSOR
AKX01417AM
2 1
3
A-43 HARNESS
CONNECTOR:
COMPONENT SIDE
AK200023
2 1
3
4
CONNECTOR: C-59
AB
C-59
HARNESS
CONNECTOR:
COMPONENT
SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-464
STEP 13. Check for continuity at crankshaft position
sensor harness side connector A-43.
(1) Disconnect the connector A-43 and measure at the harness
side.
(2) Check for the continuity between terminal No. 1 and
ground.
• Should be less than 2 ohms.
Q: Does continuity exist?
YES : Go to Step 14.
NO : Repair harness wire between crankshaft position
sensor connector A-43 (terminal No. 1) and ground
because of open circuit or harness damage. Then go
to Step 20.
STEP 14. Check connector C-59 at the MFI relay for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 15.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 20.
AK200494
1
2
3
A-43(B)
AB
CONNECTOR: A-43
HARNESS
CONNECTOR:
COMPONENT SIDE
CRANKSHAFT
POSITION
SENSOR
AKX01418 AH
2 1
3
A-43 HARNESS
CONNECTOR:
COMPONENT SIDE
AK200023
2 1
3
4
CONNECTOR: C-59
AB
C-59
HARNESS
CONNECTOR:
COMPONENT
SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст