Mitsubishi Montero Sport (2004+). Manual — part 453
DOOR
TSB Revision
BODY
42-67
NOTE: After inspecting intermediate connector C-12 inspect
the wire. If intermediate connector C-12 is damaged, repair or
replace damaged component. Refer to GROUP 00E
Harness Connector Inspection. Then go to Step 22.
Q: Are there any damaged harness wires between
ETACS-ECU connectors D-10 (terminals No.21 and
No.24) <Vehicles without keyless entry system> or D-27
(terminals No.41 and No.42) <Vehicles with keyless
entry system> and door lock actuator (front: RH)
connector F-24 (terminals No.4 and No.6)?
YES : Replace the ETACS-ECU and then go to Step 22.
NO : Repair or replace the damaged components. Refer to
GROUP 00E
, Harness Connector inspection.
Then go to Step 22.
STEP 10. Check door lock actuator (rear: RH) connector
F-21 for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q: Is the connector in good condition?
YES : Go to step 11.
NO : Repair or replace the damaged components. Refer to
GROUP 00E
, Harness Connector inspection.
Then go to Step 22.
AC309353AC
C-12
CONNECTOR: C-12
AC309455
CONNECTOR: F-21
F-21
REAR DOOR <RH>
AB
COMPONENT SIDE
DOOR
TSB Revision
BODY
42-68
STEP 11. Check the rear door lock actuator (rear: RH).
(1) Remove the door latch assembly (Refer to
(2) Follow the table to check the rear door lock actuator
(lock/unlock).
Actuator Operation Check
Q: Is the rear door lock actuator damaged?
YES : Replace the door lock actuator assembly (rear: RH),
go to Step 22.
NO : Go to Step 12.
LEVER
POSITION
BATTERY
CONNECTION
LEVER
OPERATION
At the "B" position
• Connect terminal
No. 1 and the
positive battery
terminal.
• Connect terminal
No. 2 and the
negative battery
terminal.
The lever moves
from the "B"
position to the "C"
position.
At the "C" position
• Connect terminal
No. 2 and the
positive battery
terminal.
• Connect terminal
No. 1 and the
negative battery
terminal.
The lever moves
from the "C"
position to the "B"
position.
AC003792AB
A
VIEW A
B
C
DOOR
TSB Revision
BODY
42-69
STEP 12. Check ETACS-ECU connectors D-10 <Vehicles
without keyless entry system> and D-27 <Vehicles with
keyless entry system> for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are ETACS-ECU connectors D-10 <Vehicles without
keyless entry system> and D-27 <Vehicles with keyless
entry systerm> in good condition?
YES : Go to Step 13.
NO : Repair or replace the damaged components. Refer to
GROUP 00E
, Harness Connector inspection.
Then go to Step 22.
AC202002
6 5 4
1
2
7
3
8
41
43
51
42
50
44
52
46 45
53
49
47
30
48
56
55
D-27 (B)
D-10
JUNCTION
BLOCK (REAR)
CONNECTORS: D-10, D-27
AB
D-27 COMPONENT SIDE
D-10 COMPONENT SIDE
21
22
23
24
25
26
27
28
DOOR
TSB Revision
BODY
42-70
STEP 13. Check the harness wire between ETACS-ECU
connectors D-10 (terminals No.21 and No.24) <Vehicles
without keyless entry system> or D-27 (terminals No.41
and No.42) <Vehicles with keyless entry system> and door
lock actuator (rear: RH) connector F-21 (terminals No.1
and No.2).
AC202002
6 5 4
1
2
7
3
8
41
43
51
42
50
44
52
46 45
53
49
47
30
48
56
55
D-27 (B)
D-10
JUNCTION
BLOCK (REAR)
CONNECTORS: D-10, D-27
AB
D-27 COMPONENT SIDE
D-10 COMPONENT SIDE
21
22
23
24
25
26
27
28
AC309455
CONNECTOR: F-21
F-21
REAR DOOR <RH>
AB
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст