Mitsubishi Montero Sport (2004+). Manual — part 317
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-681
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB99958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Erase the DTC.
(4) Start the engine and run it at idle.
(5) Read the DTC.
(6) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC P1603 set?
YES : Go to Step 2.
NO : The procedure is complete.
STEP 2. Measure the backup power supply voltage at PCM
connector C-90 by backprobing.
(1) Do not disconnect the PCM connector C-90.
(2) Measure the voltage between terminal No. 66 and ground
by backprobing.
• Voltage should be battery positive voltage.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 5.
NO : Go to Step 3.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AK000731
C-90 HARNESS
CONNECTOR:
HARNESS SIDE
46
57
66
45
56
65
44
55
43
49
54
64
42
48
59
41
47
58
53
63
52
62
51
61
50
60
AQ
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-682
STEP 3. Measure the backup power supply voltage at PCM
harness side connector C-90.
(1) Disconnect the PCM connector C-90 and measure at the
harness side.
(2) Measure the voltage between terminal No. 66 and ground.
• Voltage should be battery positive voltage.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 4.
NO : Repair harness wire between battery and PCM
connector C-90 (terminal No. 66) because of open
circuit or short circuit to ground. Then go to Step 6.
STEP 4. Check connector C-90 at PCM for damage.
Q: Is the harness connector in good condition?
YES : Repair harness wire between battery and PCM
connector C-90 (terminal No. 66) because of harness
damage. Then go to Step 6.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 6.
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AKX01436
41
42
43
47
48
49
58
59
50
51
60
61
52
62
53
54
63
64
55
56
57
44
45
46
65
66
C-90 HARNESS
CONNECTOR:
COMPONENT SIDE
BA
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-683
STEP 5. Check connector C-90 at PCM for damage.
Q: Is the harness connector in good condition?
YES : Replace the PCM. Then go to Step 6.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 6.
STEP 6. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Read the DTC.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC P1603 set?
YES : Repeat the troubleshooting.
NO : The procedure is complete.
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AK303629AB
MB991911
MB991827
MB991824
16-PIN
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-684
DTC P2227: Barometric Pressure Circuit Range/Performance Problem
GREEN-
YELL
OW
AK302268
Barometric Pressure Sensor Circuit
PINK
BL
ACK
BL
ACK
5V
POWERTRAIN CONTROL MODULE (PCM)
46
1
55
57
15
2
5
12
BAROMETRIC PRESSURE SENSOR
(INCORPORATED IN VOLUME
AIRFLOW SENSOR)
1 2 3 4 5 6 7
A-01
1
10
2 3 4 5 6 7 8 9
11
12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28 29 30 31 32 33
C-71
JOINT
CONNEC-
TOR (4)
47
41
42 43
48 49 50 51 52 53 54 55 56 57
46
45
44
58
59
60 61 62 63
64 65 66
C-90
(MU803781)
AK103908
CONNECTOR: A-01
BAROMETRIC
PRESSURE
SENSOR
A-01(B)
AC
AK103738AC
CONNECTOR: C-90
PCM
C-90(GR)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст