Mitsubishi Montero Sport (2004+). Manual — part 767
LOWER ARM
TSB Revision
REAR SUSPENSION
34-5
LOWER ARM BUSHING REPLACEMENT
M1341011100067
1. Use the special tools MB990891, MB99097 and MB991318,
and the press to drive out and press fit the lower arm
bushing.
2. Use the special tools MB990891 and MB991411 and the
press to press fit the lower arm bushing.
3. Position the lower arm rear bushing holes A as shown in the
illustration to align the holes A and line B, and then use the
special tools to press the lower arm rear bushings into the
lower arm. Equalize the protrusion amounts (dimensions C)
of lower arm rear bushing.
AC103765 AB
MB990891
LOWER
ARM
BUSHING
LOWER
ARM
MB990971
MB991411
MB991318
REMOVAL
PRESSFITTING
AC004194
A
A
B
C
C
AB
LOWER
ARM
SHOCK ABSORBER AND LATERAL ROD
TSB Revision
REAR SUSPENSION
34-6
SHOCK ABSORBER AND LATERAL ROD
REMOVAL AND INSTALLATION
M1341009100060
CAUTION
*: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in an unladen condition.
Required Special Tool:
• MB990650: Lower Arm Bushing Arbor
Pre-removal Operation
• Support the axle housing with a jack
AC309533AB
216
-
245 N·m*
159
-
181 ft-lb*
216
-
245 N·m*
159
-
181 ft-lb*
216
-
245 N·m*
159
-
181 ft-lb*
216
-
245 N·m*
159
-
181 ft-lb*
216
-
245 N·m*
159
-
181 ft-lb*
22 N·m
16 ft-lb
2
1
2
1
3
4
5
6
SHOCK ABSORBER REMOVAL
STEPS
1.
SHOCK ABSORBER MOUNTING
BOLT
2.
SHOCK ABSORBER
LATERAL ROD REMOVAL
STEPS
3.
PARKING BRAKE CABLE
ATTACHING BOLT (LH)
4.
SPEED SENSOR ATTACHING
BOLT (LH) <VEHICLES WITH
ABS>
5.
LOWER ARM (LH)
6.
LATERAL ROD
COIL SPRING AND AXLE BUMPER
TSB Revision
REAR SUSPENSION
34-7
LATERAL ROD BUSHING REPLACEMENT
M1341011200086
1. Use special tool MB9900650 to drive out and press in the
lateral rod bushing.
2. Install the bushing so that the projection length (A) is
uniform.
COIL SPRING AND AXLE BUMPER
REMOVAL AND INSTALLATION
M1341009400061
CAUTION
*: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in an unladen condition.
AC004222 AB
MB990650
A
A
Pre-removal Operation
• Support the axle housing with a jack
Post-installation Operation
• Brake Fluid Filling and air bleeding (Refer to GROUP
35A, On-vehicle Service
.)
AC309534AB
216
-
245 N·m*
159
-
181 ft-lb*
216
-
245 N·m*
159
-
181 ft-lb*
71 N·m
52 ft-lb
9.8 N·m
87 in-lb
15 N·m
11 ft-lb
71 N·m
52 ft-lb
12
11
9
1
10
5
7
4
3
6
8
2
1.
REAR AXLE BUMPER
COIL SPRING REMOVAL STEPS
2. BREATHER HOSE
3. PARKING BRAKE CABLE
ATTACHING BOLT
4. SPEED SENSOR ATTACHING BOLT
<VEHICLE WITH ABS>
5. BRAKE HOSE CONNECTION
COIL SPRING REMOVAL STEPS
COIL SPRING AND AXLE BUMPER
TSB Revision
REAR SUSPENSION
34-8
INSTALLATION SERVICE POINTS
.
>>A<< HELPER BRACKET INSTALLATION
Install so that the helper bracket mark comes to the front of the
vehicle.
.
>>B<< STABILIZER BAR MOUNTING BOLT INSTALLATION
1. To install the stabilizer bar, assemble the joint cups and
rubber bushings by the order and the specified direction as
shown in the figure.
2. Install the nut on the stabilizer bar mounting bolt to the
specified dimensions.
Standard value (A): 15
− 17 mm (0.6 − 0.7 inch)
6. SHOCK ABSORBER MOUNTING
BOLT (LOWER SIDE ONLY)
7. LATERAL ROD MOUNTING BOLT
(VEHICLE SIDE ONLY)
>>B<<
8. STABILIZER BAR MOUNTING BOLT
9. REAR SPRING PAD
10. COIL SPRING
11. HELPER RUBBER <VEHICLES
WITH HEAVY DUTY SUSPENSION>
>>A<<
12. HELPER BRACKET <VEHICLES
WITH HEAVY DUTY SUSPENSION>
COIL SPRING REMOVAL STEPS
AC004231
FRONT OF
VEHICLE
HELPER BRACKET
MARK
CROSSMEMBER
SIDE FRAME CROSSMEMBER
AB
AC004232 AB
A
JOINT
CUP
COLLAR
STABILIZER
BAR
JOINT CUP
MOUNTING
RUBBER
BOLT AND
NUT
BUSHING
JOINT CUP
RUBBER
BUSHING
JOINT CUP
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст