Mitsubishi Montero Sport (2004+). Manual — part 168
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-85
STEP 6. Check connector C-90 at PCM for damage.
Q: Is the connector in good condition?
YES : Replace the PCM. Then go to Step 12.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
STEP 7. Measure the ground voltage at manifold absolute
pressure sensor connector A-12 by backprobing.
(1) Do not disconnect the connector A-12.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 2 and ground by
backprobing.
• Voltage should be 0.5 volt or less.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage 0.5 volt or less?
YES : Go to Step 10.
NO : Go to Step 8.
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AK200034
2 1
3
AB
CONNECTOR: A-12
A-12(B)
HARNESS
CONNECTOR:
COMPONENT
SIDE
3
2
1
AK203038
A-12 HARNESS
CONNECTOR:
HARNESS SIDE
AF
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-86
STEP 8. Check connector A-12 at the manifold absolute
pressure sensor and connector C-90 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 9.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
AK200034
2 1
3
AB
CONNECTOR: A-12
A-12(B)
HARNESS
CONNECTOR:
COMPONENT
SIDE
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-87
STEP 9. Check for open circuit between manifold absolute
pressure sensor connector A-12 (terminal No. 2) and PCM
connector C-90 (terminal No. 57).
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 12.
NO : Repair it. Then go to Step 12.
STEP 10. Check connector A-12 at manifold absolute
pressure sensor for damage.
Q: Is the connector in good condition?
YES : Go to Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
AK200034
2 1
3
AB
CONNECTOR: A-12
A-12(B)
HARNESS
CONNECTOR:
COMPONENT
SIDE
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AK200034
2 1
3
AB
CONNECTOR: A-12
A-12(B)
HARNESS
CONNECTOR:
COMPONENT
SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-88
STEP 11. Check connector C-91 at PCM for damage.
Q: Is the connector in good condition?
YES : Replace the manifold absolute pressure sensor. Then
go to Step 12.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
STEP 12. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
Other Monitor
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0108 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
AK104028
98
78
71
88
89
76
77
72
79
91
73
80
74
75
81
92
82
83
93
84
85
94
86
87
95
96
90
97
AB
CONNECTOR: C-91
C-91(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст