Mitsubishi Montero Sport (2004+). Manual — part 410

KNUCKLE

TSB Revision

FRONT AXLE

26-21

KNUCKLE

REMOVAL AND INSTALLATION

M1261002400195

CAUTION

*: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in the unladen condition.

Required Special Tool:

• MB991897: Ball Joint Remover

Pre-removal Operation
• Front Hub Assembly Removal (Refer to

P.26-16

.)

Post-installation Operation
• Press the dust cover with a finger to check whether the

dust cover is cracked or damaged.

• Front Hub Assembly Installation (Refer to

P.26-16

.)

• Wheel Alignment Check and Adjustment (Refer to

GROUP 33A, On-vehicle Service

P.33A-3

.)

AC004662 AC

12 N·m
106 in-lb

88 - 103 N·m*
65 - 76 ft-lb*

59 - 88 N·m
43 - 65 ft-lb

44 N·m
32 ft-lb

118 - 177 N·m
87 - 131 ft-lb

N

1

8

2

7

4

N

3

6

5

REMOVAL

STEPS

1. DUST

COVER

2. FRONT SPEED SENSOR

<VEHICLES WITH ABS> (REFER
TO GROUP 35B, WHEEL SPEED
SENSOR.)

3. STABILIZER BAR CONNECTION

4. SHOCK ABSORBER LOWER

MOUNTING BOLT

<<A>>

5. TIE ROD END CONNECTION

<<A>>

6. LOWER ARM BALL JOINT

CONNECTION

<<A>>

7. UPPER ARM BALL JOINT

CONNECTION

8. KNUCKLE

REMOVAL STEPS (Continued)

KNUCKLE

TSB Revision

FRONT AXLE

26-22

REMOVAL SERVICE POINT

.

<<A>> TIE ROD END/UPPER ARM BALL JOINT DISCON-
NECTION

CAUTION

• Do not remove the nut from the ball joint. Loosen it and

use the special tool to avoid possible damage to ball
joint threads.

• Hang the special tool with a cord to prevent from fall-

ing.

1. Install special tool MB991897 as shown in the figure.

2. Turn the bolt and knob as necessary to make the jaws of

special tool MB991897 parallel, tighten the bolt by hand and
confirm that the jaws are still parallel.
NOTE: When adjusting the jaws in parallel, make sure the
knob is in the position shown in the figure.

3. Tighten the bolt with a wrench to disconnect the tie rod end.

INSPECTION

M1261002500169

Check the knuckle for wear or cracks.

AC106820 AB

CORD

BOLT

MB991897

NUT

BALL JOINT

AC106821

KNOB

PARALLEL

BOLT

CORRECT

WRONG

AC

KNUCKLE

TSB Revision

FRONT AXLE

26-23

DISASSEMBLY AND ASSEMBLY <4WD>

M1261003200064

Required Special Tools:

• MB990938: Bar

• MB990939: Brass Bar

• MB990956: Needle Bearing Installer

• MB990985: Oil Seal Installer

DISASSEMBLY SERVICE POINT

.

<<A>> NEEDLE BEARING REMOVAL
1. Remove the oil seal and take out the spacer.
2. Drive out the needle bearing by tapping the needles

uniformly.

AC004676 AB

4

3

2

1

3

2

1

N

N

DISASSEMBLY

STEPS

>>C<<

1. OIL

SEAL

>>B<<

2. SPACER

<<A>> >>A<<

3. NEEDLE BEARING

4. KNUCKLE

DISASSEMBLY

STEPS

(Continued)

AC004677AB

MB990939

KNUCKLE

TSB Revision

FRONT AXLE

26-24

ASSEMBLY SERVICE POINTS

.

>>A<< NEEDLE BEARING INSTALLATION

CAUTION

Use care to prevent driving the needle bearing too far in.
1. Apply multipurpose grease to the roller surface of the new

needle bearing.

2. Use the special tools MB990938, MB990956 to press-fit the

needle bearing until it is flush with the knuckle end face.

.

>>B<< SPACER INSTALLATION
1. Apply multipurpose grease to the knuckle attachment

surface of the spacer.

2. Install the spacer to the knuckle with the chamfered side

toward the center of vehicle.

.

>>C<< OIL SEAL INSTALLATION
1. Use the special tools MB990938, MB990985 to press-fit the

new oil seal until it is flush with the knuckle end face.

2. Apply multipurpose grease to the inside and lip of the oil

seal.

AC004678 AB

MB990956

MB990938

MB990956

AC004679AB

AC004680AB

MB990985

MB990985

MB990938