Mitsubishi Montero Sport (2004+). Manual — part 161
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-57
STEP 4. Check connector A-12 at the manifold absolute
pressure sensor and connector C-90 at PCM for damage.
Q: Is the connector in good condition?
YES : Repair harness wire between manifold absolute
pressure sensor connector A-12 (terminal No. 3) and
PCM connector C-90 (terminal No. 46) because of
open circuit or harness damage. Then go to Step 12.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
AK200034
2 1
3
AB
CONNECTOR: A-12
A-12(B)
HARNESS
CONNECTOR:
COMPONENT
SIDE
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-58
STEP 5. Check connector A-12 at the manifold absolute
pressure sensor and connector C-90 at PCM for damage.
Q: Is the connector in good condition?
YES : Replace the PCM. Then go to Step 12.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
STEP 6. Measure the ground voltage at manifold absolute
pressure sensor connector A-12 by backprobing.
(1) Do not disconnect the connector A-12.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 2 and ground by
backprobing.
• Voltage should be 0.5 volt or less.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage 0.5 volt or less?
YES : Go to Step 9.
NO : Go to Step 7.
AK200034
2 1
3
AB
CONNECTOR: A-12
A-12(B)
HARNESS
CONNECTOR:
COMPONENT
SIDE
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AK200034
2 1
3
AB
CONNECTOR: A-12
A-12(B)
HARNESS
CONNECTOR:
COMPONENT
SIDE
3
2
1
AK203038
A-12 HARNESS
CONNECTOR:
HARNESS SIDE
AF
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-59
STEP 7. Check connector A-12 at the manifold absolute
pressure sensor and connector C-90 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 8.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
AK200034
2 1
3
AB
CONNECTOR: A-12
A-12(B)
HARNESS
CONNECTOR:
COMPONENT
SIDE
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-60
STEP 8. Check for harness damage between manifold
absolute pressure sensor connector A-12 (terminal No. 2)
and PCM connector C-90 (terminal No. 57).
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 12.
NO : Repair it. Then go to Step 12.
STEP 9. Check connector A-12 at manifold absolute
pressure sensor for damage.
Q: Is the connector in good condition?
YES : Go to Step 10.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
AK200034
2 1
3
AB
CONNECTOR: A-12
A-12(B)
HARNESS
CONNECTOR:
COMPONENT
SIDE
AK103762
42
43
48
49
50
51
52
53
54
55
56
57
46 45 44
58
59
60
61
62
63
64
65
66
47
41
AB
CONNECTOR: C-90
C-90(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AK200034
2 1
3
AB
CONNECTOR: A-12
A-12(B)
HARNESS
CONNECTOR:
COMPONENT
SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст