Mitsubishi Montero Sport (2004+). Manual — part 607
CONDENSER AND CONDENSER FAN MOTOR
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55-55
REMOVAL SERVICE POINT
.
<<A>> DISCHARGE HOSE/LIQUID PIPE A DISCONNEC-
TION
CAUTION
Seal the hoses completely, otherwise the compressor oil
and receiver will absorb water vapor easily, possibly dam-
aging the compressor and deteriorating performance.
Plug the disconnected hose, pipe and condenser nipple to pre-
vent foreign matter from getting into them.
INSTALLATION SERVICE POINT
.
>>A<< CONDENSER INSTALLATION
When replacing the condenser, refill with a specified amount of
compressor oil and install it (to the vehicle).
Compressor oil: SUN PAG56
Quantity: 20 cm
3
(0.7 floz)
INSPECTION
M1556001100129
CONDENSER FAN MOTOR CHECK
Check to be sure that the condenser fan motor operates when
battery voltage is applied to terminal 1 and terminal 2
grounded.
AC002870AB
REFRIGERANT LINE
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55-56
REFRIGERANT LINE
REFRIGERANT LINE
M1552006400253
WARNING
When removing and installing the suction pipe or discharge pipe C from vehicles equipped
with SRS, do not let it bump against the front impact sensor (RH).
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
• Refrigerant Discharging and Charging (Refer to
• Radiator Grill Removal and Installation (Refer to GROUP
51,Grill, Molding and Garnish
.)
• Front Bumper Removal and Installation (Refer to GROUP
• Battery Removal and installation
• Windshield Washer Tan Removal and Installation (Refer
to GROUP 51, Windshield Wiper and Washer
.)
AC002871 AB
1
2
3
4
5
6
7
8
9
10
PIPING CONNECTION
COMPRESSOR OIL:
SUN PAG56
N
6
N
6
N
6
N
6
REMOVAL STEPS
>>A<<
1.
SUCTION HOSE
<<A>>
2.
SUCTION PIPE A
<<A>>
3.
LIQUID PIPE A
<<A>>
4.
DISCHARGE HOSE
REMOVAL STEPS (Continued)
REFRIGERANT LINE
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55-57
REMOVAL SERVICE POINT
.
<<A>> HOSE, PIPE AND RECEIVER ASSEMBLY DISCON-
NECTION
CAUTION
Seal the hoses completely, otherwise the compressor oil
and receiver will absorb water vapor easily, possibly dam-
aging the compressor and deteriorating performance.
Plug the disconnected hose, pipe, condenser, compressor and
heater unit nipple to prevent foreign matter from getting into
them.
INSTALLATION SERVICE POINT
.
>>A<< SUCTION HOSE/RECEIVER ASSEMBLY INSTALLA-
TION
CAUTION
Seal the hoses completely, otherwise the compressor oil
and receiver will absorb water vapor easily, possibly dam-
aging the compressor and deteriorating performance.
Plug the disconnected hose, pipe, condenser, compressor and
heater unit nipple to prevent foreign matter from getting into
them.
Compressor oil: SUN PAG56
Quantity: Suction hose: 10cm
3
(0.3 floz)
Receiver assembly: 10 cm
3
(0.3 floz)
<<A>>
5.
LIQUID PIPE
6.
O-RING
7.
SUCTION PIPE BRACKET
<<A>>
>>A<<
8.
RECEIVER ASSEMBLY
9.
DUAL PRESSURE SWITCH
10. RECEIVER BRACKET
REMOVAL STEPS (Continued)
AMBIENT AIR TEMPERATURE SENSOR
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55-58
AMBIENT AIR TEMPERATURE SENSOR
REMOVAL AND INSTALLATION
M1554017500012
INSPECTION
M1556001100174
AMBIENT AIR TEMPERATURE CHECK
WARNING
The temperature conditions when checking should
not exceed the range shown in the diagram.
When the resistance between the sensor terminals is mea-
sured under two or more temperature conditions the resistance
should approximately satisfy the illustrated values.
Pre-removal and Post-installation Operation
Front Bumper Removal and Installation (Refer to GROUP
51, Front Bumper
AC002872
AMBIENT AIR TEMPERATURE
SENSOR
AD
AC003135
RESISTANCE
Ω
k
TEMPERATURE ˚C (˚F)
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст