Mitsubishi Montero Sport (2004+). Manual — part 345
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-793
STEP 7. Using scan tool MB991958, check data list item 39:
Right Bank heated oxygen sensor (front).
(1) Start the engine and run at idle.
(2) Set scan tool MB991958 to the data reading mode for item
39, Right Bank Heated Oxygen Sensor (front).
• Warm up the engine. When the engine is decelerated
suddenly from 4000 r/min, the output voltage should
increase from 200 millivolts or less to 600
− 1000 milli-
volts in a few seconds.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : Go to Step 8.
NO : Refer to DTC P0130
− Heated Oxygen Sensor Circuit
(bank 1, sensor 1)
, DTC P0131
− Heated
Oxygen Sensor Circuit low voltage (bank 1, sensor 1)
, DTC P0132
− Heated Oxygen Sensor
Circuit High Voltage (bank 1, sensor 1)
P0133
− Heated Oxygen Sensor Circuit Slow
Response (bank 1, sensor 1)
−
Heated Oxygen Sensor Circuit No Activity Detected
(bank 1, sensor 1)
STEP 8. Using scan tool MB991958, check data list item 11:
Left Bank Heated oxygen sensor (front).
(1) Start the engine and run at idle.
(2) Set scan tool MB991958 to the data reading mode for item
11, Left Bank Heated Oxygen Sensor (front).
• Output voltage should measure 0.6 − 1.0 volt when sud-
den revving.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : Go to Step 9.
NO : Refer to DTC P0150
− Heated Oxygen Sensor Circuit
(bank 2, sensor 1)
, DTC P0151
− Heated
Oxygen Sensor Circuit low voltage (bank 2, sensor 1)
, DTC P0152
− Heated Oxygen Sensor
Circuit High Voltage (bank 2, sensor 1)
P0153
− Heated Oxygen Sensor Circuit Slow
Response (bank 2, sensor 1)
−
Heated Oxygen Sensor Circuit No Activity Detected
(bank 2, sensor 1)
AK303629AB
MB991911
MB991827
MB991824
16-PIN
AK303629AB
MB991911
MB991827
MB991824
16-PIN
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-794
STEP 9. Using scan tool MB991958, check data list item 39:
Right Bank Heated oxygen sensor (front).
(1) Start the engine and run at idle.
(2) Set scan tool MB991958 to the data reading mode for item
39, Right Bank Heated Oxygen Sensor (front).
• Voltage should fluctuate between 0 − 0.4 volt and 0.6 −
1.0 volt while after the engine has been warmed.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : Go to Step 10.
NO : Go to Step 12.
STEP 10. Check the EGR system.
Refer to GROUP 17, Emission Control System
− EGR System
Check
.
Q: Is the EGR system normal?
YES : Go to Step 11.
NO : Repair or replace. Then confirm that the malfunction
symptom is eliminated.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-795
STEP 11. Using scan tool MB991958, check data list item
69: Right Bank Heated oxygen sensor (rear).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB9919958 to the data link connector.
(2) Start the engine and run at idle.
(3) Set scan tool MB991958 to the data reading mode for item
69, Right Bank Heated Oxygen Sensor (rear).
• Average voltage should measure 0.6 volt or less, when
idling.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : Go to Step 16.
NO : Replace the right bank heated oxygen sensor (front).
Then confirm that the malfunction symptom is
eliminated.
STEP 12. Using scan tool MB991958, check data list item
11: Left Bank Heated oxygen sensor (front).
(1) Start the engine and run at idle.
(2) Set scan tool MB991958 to the data reading mode for item
11, Left Bank Heated Oxygen Sensor (front).
• Warm up the engine. When the engine is decelerated
suddenly from 4000 r/min, the output voltage should
increase from 200 millivolts or less to 600
− 1000 milli-
volts in a few seconds.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : Go to Step 13.
NO : Go to Step 15.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
AK303629AB
MB991911
MB991827
MB991824
16-PIN
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-796
STEP 13. Check the EGR system.
Refer to GROUP 17, Emission Control System
− EGR System
Check
.
Q: Is the EGR system normal?
YES : Go to Step 14.
NO : Repair or replace. Then confirm that the malfunction
symptom is eliminated.
STEP 14. Using scan tool MB991958, check data list item
59: Left Bank Heated oxygen sensor (rear).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Start the engine and run at idle.
(3) Set scan tool MB991958 to the data reading mode for item
59, Left Bank Heated Oxygen Sensor (rear).
• Average voltage should measure 0.6 volt or less, when
idling.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : Go to Step 16.
NO : Replace the left bank heated oxygen sensor (front).
Then confirm that the malfunction symptom is
eliminated.
STEP 15. Check the fuel pressure.
Refer to On-vehicle Service
− Fuel Pressure Test
Q: Is the fuel pressure normal?
YES : Go to Step 16.
NO : Repair or replace. Then confirm that the malfunction
symptom is eliminated.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст