Mitsubishi Montero Sport (2004+). Manual — part 344
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-789
STEP 3. Using scan tool MB991958, check data list.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check the following items in the data list. Refer to Data List
Reference Table
a. Item 21: Engine Coolant Temperature Sensor.
b. Item 13: Intake Air Temperature Sensor.
c. Item 25: Barometric pressure Sensor.
d. Item 69: Right Bank Heated Oxygen Sensor (rear)
e. Item 39: Right Bank Heated Oxygen Sensor (front)
f. Item 59: Left Bank Heated Oxygen Sensor (rear)
g. Item 11: Left Bank Heated Oxygen Sensor (front)
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Are they operating properly?
YES : Go to Step 4.
NO : Repair or replace. Then confirm that the malfunction
symptom is eliminated.
STEP 4. Using scan tool MB991958, check data list.
(1) Turn the ignition switch to the "ON" position.
(2) Check the following items of the data list. Refer to, Data List
Reference Table
a. Item 39: Right Bank Heated Oxygen Sensor (front)
b. Item 11: Left Bank Heated Oxygen Sensor (front)
• Voltage should fluctuate between 0 − 0.4 volt and 0.6 −
1.0 volt while idling after the engine has been warmed.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : Replace the heated oxygen sensor (front). Then
confirm that the malfunction symptom is eliminated. If
not resolved, go to step 6.
NO : Go to Step 5.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
AK303629AB
MB991911
MB991827
MB991824
16-PIN
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-790
STEP 5. Check the fuel pressure.
Refer to On-vehicle Service
− Fuel Pressure Test
Q: Is the fuel pressure normal?
YES : Go to Step 6.
NO : Repair or replace. Then confirm that the malfunction
symptom is eliminated.
STEP 6. Check the following items.
(1) Check the following items, and repair or replace the
defective items.
a. Check the injectors for fuel leakage.
b. Check the ignition coil, spark plugs, spark plug cables.
c. Check compression pressure.
d. Check the positive crank case ventilation system.
e. Check the evaporative emission system.
f. Check the EGR system.
(2) Then check the malfunction symptom.
Q: Is the malfunction symptom is eliminated.
YES : The check is completed.
NO : Replace the catalytic converter. Then confirm that the
malfunction symptom is eliminated.
INSPECTION PROCEDURE 23: Transient, Mass Emission Tailpipe Test Failure.
.
COMMENT
• The test is failed when the air/fuel ratio is not con-
trolled to the ideal air/fuel ratio. This occurs due
to the feedback control by heated oxygen sensor
signals, insufficient EGR flow rate, or deteriorated
catalyst.
NOTE: If the three-way catalyst temperature is low
when checking the exhaust gas, the three-way cata-
lyst cannot sufficiently clean the emissions. Warm up
the engine sufficiently before checking the exhaust,
and check immediately.
.
TROUBLESHOOTING HINTS (The most likely
causes for this case: )
• Malfunction of air/fuel ratio control system.
• Malfunction of the EGR system.
• Deteriorated catalyst.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I
• MB991827: USB Cable
• MB991911: Main Harness B
STEP 1. Check the exhaust gas with the engine at normal
operating temperature.
Q: After enough warm up, was the exhaust gas checked
enough?
YES : Go to Step 2.
NO : Check it again after enough warm up.
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-791
STEP 2. Check the following items.
(1) Check the following items.
a. Check all vacuum hoses and connectors.
b. Check electrical wires and connectors for obvious prob-
lems.
c. Check the exhaust system for missing or damaged
parts.
Q: Are they normal?
YES : Go to Step 3.
NO : Repair or replace. Then confirm that the malfunction
symptom is eliminated.
STEP 3. Check the drivability.
(1) Check if the malfunction symptom described on the
symptom chart is occurring.
Q: Is the drivability normal?
YES : Go to Step 4.
NO : Refer to Trouble Symptom Chart
.
STEP 4. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Read the DTC.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC set?
YES : Refer to Diagnostic Trouble Code Chart
NO : Go to Step 5.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-792
STEP 5. Check the ignition timing.
Refer to GROUP 11A, On-vehicle Service
− Ignition Timing
Check
Q: Is the ignition timing normal?
YES : Go to Step 6.
NO : Check that the crankshaft position sensor and timing
belt cover are in the correct position. Then confirm
that the malfunction symptom is eliminated.
STEP 6. Using scan tool MB991958, check data list.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check the following items in the data list. Refer to Data List
Reference Table
a. Item 21: Engine Coolant Temperature Sensor.
b. Item 13: Intake Air Temperature Sensor.
c. Item 25: Barometric pressure Sensor.
d. Item 69: Right Bank Heated Oxygen Sensor (rear)
e. Item 59: Left Bank Heated Oxygen Sensor (rear)
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : Go to Step 7.
NO : Repair or replace. Then confirm that the malfunction
symptom is eliminated.
AK303629AB
MB991911
MB991827
MB991824
16-PIN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст