Mitsubishi Montero Sport (2004+). Manual — part 126
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-99
AUTO-CRUISE CONTROL
REMOVAL AND INSTALLATION
M1172001400337
<VACUUM PUMP>
AC004514
4.9 N·m
43 in-lb
4.9 N·m
43 in-lb
1.5 N·m
13 in-lb
14 N·m
122 in-lb
3
7
6
5
4
1
2
AB
REMOVAL STEPS
1.
VACUUM HOSE CONNECTION
2.
VACUUM PUMP CONNECTOR
3.
ACTUATOR BRACKET
4.
VACUUM PUMP ASSEMBLY
5.
DISTANCE PIECE
6.
RUBBER MOUNT
7.
PUMP BRACKET
REMOVAL STEPS (Continued)
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-100
<SWITCHES, CONTROL UNIT AND SENSORS>
WARNING
Before removal of the air bag module, refer to GROUP 52B, SRS Service Precautions
, and GROUP 52B, Air Bag Module and Clock Spring
.
AC004515 AB
4.9 N·m
43 in-lb
13
10
11
9
8
12
CONTROL SWITCH REMOVAL
STEPS
•
AIR BAG MODULE (REFER TO
GROUP 52B, AIR BAG MODULE
AND CLOCK SPRING
8.
AUTO-CRUISE CONTROL
SWITCH
CONTROL UNIT REMOVAL
STEPS
•
COWL SIDE TRIM (REFER TO
GROUP52A, TRIM
).
9.
AUTO-CRUISE CONTROL-ECU
SENSOR REMOVAL STEPS
10. THROTTLE POSITION SENSOR
(REFER TO GROUP 13A,
THROTTLE POSITION SENSOR
).
11. STOPLIGHT SWITCH (REFER TO
GROUP 35A, BRAKE PEDAL
12. PARK/NEUTRAL POSITION
SWITCH (REFER TO GROUP
23B, TRANSMISSION
13. VEHICLE SPEED SENSOR
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-101
AUTO-CRUISE CONTROL SWITCH CHECK
M1172001500077
Measure the resistance between the terminals when each of
the "SET," "RESUM," "CANCEL" and "MAIN" switches is
pressed. If the values measured at the time correspond to
those in the table below, the resistance values are correct.
SWITCH
POSITION
RESISTANCE BETWEEN TERMINALS
"MAIN" switch
"OFF"
Terminals 1 and 2 Open circuit
"MAIN" switch
"ON"
Terminals 1 and 2 Approximately 3.9 k
Ω
"CANCEL" switch
ON
Terminals 2 and 3 Approximately 0
Ω
"RESUME"
switch ON
Terminals 2 and 3 Approximately 910
Ω
"SET" switch ON Terminals 2 and 3 Approximately 220
Ω
1 2 3
AC102096AB
OFF
OFF
OFF
OFF
ON
ON
ON
ON
CAN
MAIN
RES
SET
1
2
3
EMISSION CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-102
EMISSION CONTROL
GENERAL DESCRIPTION
M1173000100228
The emission control system consists of the fol-
lowing subsystems:
• Positive crankcase ventilation system
• Evaporative emission system
• Exhaust emission control system
DIAGNOSIS
M1173000700093
SPECIAL TOOLS
M1173000600115
SYMPTOM
PROBABLE CAUSE
REMEDY
Engine will not start or hard
to start
Vacuum hose disconnected or damaged Repair or replace
The EGR valve is not closed.
Repair or replace
Malfunction of the evaporative emission
purge solenoid
Repair or replace
Rough idle or engine stalls
The EGR valve is not closed.
Repair or replace
Vacuum hose disconnected or damaged. Repair or replace
Malfunction of the positive crankcase
ventilation valve
Replace
Malfunction of the purge control system
Check the system; If there is a
problem, check its component
parts.
Engine hesitates or poor
acceleration
Malfunction of the exhaust gas
recirculation system
Check the system; If there is a
problem, check its component
parts.
Excessive oil consumption
Positive crankcase ventilation line
clogged
Check positive crankcase
ventilation system
Poor fuel mileage
Malfunction of the exhaust gas
recirculation system
Check the system; If there is a
problem, check its component
parts.
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MD998770
Oxygen sensor wrench
MD998770-01 or General
service tool
Removal/installation of
heated oxygen sensor
MB995061
Purge flow indicator
MLR6890A
Inspection of purge
control system
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст