Mitsubishi Montero Sport (2004+). Manual — part 89
ON-VEHICLE SERVICE
TSB Revision
ENGINE LUBRICATION
12-3
ON-VEHICLE SERVICE
ENGINE OIL CHECK
M1121000900223
1. Pull out the oil dipstick slowly and check that the oil level is
within the marks on the oil dipstick.
2. Check that the oil is not excessively dirty, that there is no
coolant or gasoline mixed in, and that it is sufficiently thick
and slippery.
ENGINE OIL REPLACEMENT
M1121001000234
Refer to GROUP 00, Maintenance Service
− Engine Oil
ENGINE OIL FILTER REPLACEMENT
M1121001100253
Refer to GROUP 00, Maintenance Service
− Engine Oil Filter
ENGINE OIL PRESSURE CHECK
M1121002300391
Required Special Tool:
MD998054: Engine Oil Pressure Switch Wrench
1. Check engine oil quantity.
2. Remove the engine oil pressure switch terminal.
CAUTION
Since sealant is applied to the thread of the engine oil
pressure switch, take care not to damage the engine oil
pressure switch when removing it.
3. Use special tool MD998054 to remove the engine oil
pressure switch.
4. Install the engine oil pressure gauge.
NOTE: Use a 1/8 pipe thread adapter.
5. Run the engine to warm it.
6. After the engine has been warmed up, check that engine oil
pressure is within the standard value.
Standard value:
At idle: 29 kPa (4.2 psi) or more
At 3,500 r/min: 294
− 686 kPa (43 − 100 psi)
7. Remove the engine oil pressure gauge.
ACX00892AB
GOOD
MAXIMUM
MINIMUM
AKX00293
CYLINDER BLOCK
OIL FILTER
BRACKET
ENGINE OIL
PRESSURE
SWITCH
AKX00293AD
AKX00294
MD998054
AB
SPECIFICATIONS
TSB Revision
ENGINE LUBRICATION
12-4
8. Apply the specified sealant 3M
AAD Part number 8672 or
equivalent to thread of the engine oil pressure switch.
CAUTION
Do not start the engine within one hour after the engine oil
pressure switch has been installed.
9. Use special tool MD998054 to tighten the engine oil
pressure switch to the specified torque.
Tightening torque: 10
± 2 N⋅m (87 ± 17 in-lb)
10.Install the engine oil pressure switch terminal.
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATION
M1121002200327
SERVICE SPECIFICATIONS
M1121000300221
SEALANT
M1121000500225
LUBRICANT
M1121000400499
.
AKX00295 AB
AKX00294
MD998054
AB
ITEM
SPECIFICATION
Engine oil pressure switch
10
± 2 N⋅m (87 ± 17 in-lb)
ITEM
STANDARD VALUE
Engine oil pressure kPa (psi)
at idle
29 (4.2) or more
at 3,500 r/min
294
− 686 (43 − 100)
ITEM
SPECIFIED SEALANT
Engine oil pressure switch
3M
AAD Part No. 8672 or equivalent
ITEM
ENGINE OIL
QUANTITY dm
3
(qt)
Oil filter
Engine oils displaying ILSAC certification
symbol ("Starburst" symbol) or conforming to
the API classification SL, SL/CF.
0.3 (0.32)
Total quantity
4.6 (4.82)
SPECIFICATIONS
TSB Revision
ENGINE LUBRICATION
12-5
ENGINE OIL
CAUTION
Never use nondetergent or straight mineral oil.
Use only engine oils displaying the ILSAC certification mark
("Starburst" symbol) on the container.
If these oils are not available, an API classification SL or SL/CF
can be used.
ACX00394AI
ILSAC CERTIFICATION MARK
("STARBURST" SYMBOL)
A
P
I
SE
RVICE S
L/C
F
SAE
5W-30
AC308969
API SERVICE SYMBOL
AB
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст