Mitsubishi Montero (2002-2004). Manual — part 722
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-585
STEP 4. Check for short circuit to ground between throttle
actuator control motor connector B-05 (terminal No. 6) and
PCM connector D-136 (terminal No. 133).
Q: Is the harness wire in good condition?
YES : Go to Step 5.
NO : Repair it. Then go to Step 7.
AK201174
1
6 5 4 3 2
B-05(B)
CONNECTOR: B-05
HARNESS
CONNECTOR:
COMPONENT SIDE
AB
AK201170
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
CONNECTOR: D-136
PCM
D-136(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AB
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-586
STEP 5. Check for short circuit to ground between throttle
actuator control motor connector B-05 (terminal No. 5) and
PCM connector D-136 (terminal No. 141).
Q: Is the harness wire in good condition?
YES : Go to Step 6.
NO : Repair it. Then go to Step 7.
STEP 6. Using scan tool MB991502, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is DTC P2102 set?
YES : Replace the PCM. Then go to Step 7.
NO : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use Troubleshooting/
Inspection Service Points
AK201174
1
6 5 4 3 2
B-05(B)
CONNECTOR: B-05
HARNESS
CONNECTOR:
COMPONENT SIDE
AB
AK201170
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
CONNECTOR: D-136
PCM
D-136(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AB
ACX01539
16-PIN
MB991502
AC
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-587
STEP 7. Using scan tool MB991502, read the diagnostic
trouble code (DTC).
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is DTC P2102 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
P2103 Throttle Actuator Control Motor Circuit (Shorted High)
ACX01539
16-PIN
MB991502
AC
AK201462
GREEN-
WHITE
GREEN-
YELL
OW
B-05
133
6
THROTTLE
ACTUATOR
CONTROL
MOTOR
POWERTRAIN
CONTROL
MODULE
141
5
6
1 2 3 4 5
D-136
(MU803801)
121122
123
125126127128129 130 131 132
134135
136 137 138 139 140
142143
144
145
124
133
141
146
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-588
.
CIRCUIT OPERATION
• Controls the current that is applied from the PCM
(terminals No. 133, No. 141) to the throttle actua-
tor control motor (terminals No. 5, No. 6).
.
TECHNICAL DESCRIPTION
• PCM varies the direction and the amperage of
the current that is applied to the throttle actuator
control motor in order to control the opening of
the throttle valve.
.
DTC SET CONDITIONS
Check Conditions
• Battery positive voltage is higher than 8.3 volts
Judgement Criteria
• Throttle actuator control motor current is 8
amperes or higher for 0.16 seconds.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
• Throttle actuator control motor failed or malad-
justed.
• Open or shorted throttle actuator control motor
circuit, or loose connector.
• PCM failed.
DIAGNOSIS
Required Special Tool:
• MB991502: Scan Tool (MUT-II)
STEP 1. Check connector B-05 at throttle actuator control
motor for damage.
Q: Is the connector in good condition?
YES : Go to Step 2.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 7.
AK201173AC
THROTTLE
ACTUATOR
CONTROL
MOTOR
AK201038AI
CONNECTOR: D-136
PCM
D-136(GR)
AK201174
1
6 5 4 3 2
B-05(B)
CONNECTOR: B-05
HARNESS
CONNECTOR:
COMPONENT SIDE
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст