Mitsubishi Montero (2002-2004). Manual — part 720
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-577
STEP 8. Using scan tool MB991502, read the diagnostic
trouble code (DTC).
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is DTC P2100 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
P2101 Throttle Actuator Control Motor Magneto Malfunction
ACX01539
16-PIN
MB991502
AC
AK201462
GREEN-
WHITE
GREEN-
YELL
OW
B-05
133
6
THROTTLE
ACTUATOR
CONTROL
MOTOR
POWERTRAIN
CONTROL
MODULE
141
5
6
1 2 3 4 5
D-136
(MU803801)
121122
123
125126127128129 130 131 132
134135
136 137 138 139 140
142143
144
145
124
133
141
146
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-578
.
TECHNICAL DESCRIPTION
• PCM check whether the throttle actuator control
motor magneto has failed.
.
DTC SET CONDITIONS
Check Condition
• Battery positive voltage is higher than 8.3 volts.
Judgement Criteria
• The coil temperature of the throttle actuator con-
trol motor should be 180
°C (356°F) or higher for
0.16 seconds.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
• Throttle actuator control motor failed or malad-
justed.
• Open or shorted throttle actuator control motor
circuit, or loose connector.
• PCM failed.
DIAGNOSIS
Required Special Tool:
• MB991502: Scan Tool (MUT-II)
STEP 1. Check connector B-05 at throttle actuator control
motor for damage.
Q: Is the connector in good condition?
YES : Go to Step 2.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 7.
AK201173AC
THROTTLE
ACTUATOR
CONTROL
MOTOR
AK201038AI
CONNECTOR: D-136
PCM
D-136(GR)
AK201174
1
6 5 4 3 2
B-05(B)
CONNECTOR: B-05
HARNESS
CONNECTOR:
COMPONENT SIDE
AB
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-579
STEP 2. Check the throttle actuator control motor.
(1) Disconnect the connector B-05.
(2) Measure the resistance between throttle actuator control
motor side connector terminal No. 5 and No. 6.
Standard value: 0.3
− 100 ohms
Q: Is the measured resistance between 0.3 and 100 ohms?
YES : Go to Step 3.
NO : Replace the throttle body ASSY. Then go to Step 7.
STEP 3. Check connector D-136 at PCM for damage
Q: Is the connector in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 7.
AK201174
1
6 5 4 3 2
B-05(B)
CONNECTOR: B-05
HARNESS
CONNECTOR:
COMPONENT SIDE
AB
6
1 2 3 4 5
AK201513AB
THROTTLE ACTUATOR
CONTROL MOTOR
SIDE CONNECTOR
AK201170
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
CONNECTOR: D-136
PCM
D-136(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AB
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-580
STEP 4. Check for short circuit to ground and harness
damage between throttle actuator control motor connector
B-05 (terminal No. 6) and PCM connector D-136 (terminal
No. 133).
Q: Is the harness wire in good condition?
YES : Go to Step 5.
NO : Repair it. Then go to Step 7.
AK201174
1
6 5 4 3 2
B-05(B)
CONNECTOR: B-05
HARNESS
CONNECTOR:
COMPONENT SIDE
AB
AK201170
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
CONNECTOR: D-136
PCM
D-136(GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст