Mitsubishi Montero (2002-2004). Manual — part 282
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-175
STEP 22. Check at rear power window sub-switch
connector H-02 in order to check the power window relay
circuit of the power supply to the rear power window sub-
switch (LH).
(1) Disconnect rear power window sub-switch (LH) connector
H-02, and measure at the harness side.
(2) Measure the voltage between terminal 4 and ground.
• The voltage should measure approximately 12 volts
(battery positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 26.
NO : Go to Step 23.
STEP 23. Check power window relay connector D-219 and
rear power window sub-switch (LH) connector H-02 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are power window relay connector D-219 and rear
power window sub-switch (LH) connector H-02 in good
condition?
YES : Go to Step 24.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the rear power window sub-
switch (LH) should now work normally.
AC204312
1
2
3
4
5
6
AC
CONNECTOR H-02
(HARNESS SIDE)
AC203850AB
CONNECTOR: D-219
JUNCTION BLOCK
(FRONT VIEW)
D-219
1
2
3
4
5
JUNCTION
BLOCK SIDE
D-219
AC000237 AE
H-02
CONNECTOR: H-02
REAR DOOR<LH>
H-02
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-176
STEP 24. Check the harness wiring between power
window relay connector D-219 (terminal 4) and rear power
window sub-switch (LH) connector H-02 (terminal 4).
AC203850AB
CONNECTOR: D-219
JUNCTION BLOCK
(FRONT VIEW)
D-219
1
2
3
4
5
JUNCTION
BLOCK SIDE
D-219
AC000237AF
H-02
CONNECTOR: H-02
REAR DOOR<LH>
H-02
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-177
NOTE: Also check junction block connector D-208 and inter-
mediate connectors D-125 and F-12. If junction block connec-
tor D-208, intermediate connector D-125 or F-12 is damaged,
repair or replace the connector as described in GROUP 00E,
Harness Connector Inspection
.
Q: Is the harness wiring between power window relay
connector D-219 (terminal 4) and rear power window
sub-switch (LH) connector H-02 (terminal 4) in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the rear power window sub-switch (LH) should now
work normally.
AC203850AD
CONNECTOR: D-208
JUNCTION BLOCK
(FRONT VIEW)
D-208
D-208
1
2
3 4 5 6
AC203859 AD
CONNECTOR: D-125
D-125
D-125
AC204484
AE
F-23
F-23
CONNECTORS: F-12, F-23
F-12
F-12
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-178
STEP 25. Check at rear power window sub-switch (LH)
connector H-02 in order to check the ground circuit to the
rear power window sub-switch (LH).
(1) Disconnect rear power window sub-switch (LH) connector
H-02, and measure at the harness side.
(2) Measure the resistance value between terminal 5 and
ground.
• The resistance should measure 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 29.
NO : Go to Step 26.
STEP 26. Check power window main switch connector H-
05 and rear power window sub-switch (LH) connector H-02
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are power window main switch connector H-05 and rear
power window sub-switch (LH) connector H-02 in good
condition?
YES : Go to Step 27.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the rear power window sub-
switch (LH) should now work normally.
AC000237AF
H-02
CONNECTOR: H-02
REAR DOOR<LH>
H-02
(HARNESS SIDE)
AC204323
1
2
3
4
5
6
AD
CONNECTOR H-02
(HARNESS SIDE)
AC203774
CONNECTOR: H-05
AE
DRIVER'S DOOR
H-05
H-05
AC000237 AE
H-02
CONNECTOR: H-02
REAR DOOR<LH>
H-02
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст