Mitsubishi Montero (2002-2004). Manual — part 935
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-223
STEP 8. Using an oscilloscope, check the output shaft
speed sensor waveform at PCM connector D-134 by
backprobing.
(1) Do not disconnect connector D-134.
(2) Connect an oscilloscope probe to PCM connector D-134
terminal 73 and terminal 88 by backprobing.
(3) Start the engine and drive the vehicle at a constant speed of
50 km/h (31 mph). (Gear range: 3rd gear)
(4) Check the output shaft speed sensor waveform.
• The output shaft speed sensor waveform should show a
pattern similar to the illustration. The maximum value
should be 4.8 volts and more and the minimum value
0.8 volt and less. The output waveform should not con-
tain electrical noise.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the waveform normal?
YES : Go to Step 13.
NO : Go to Step 9.
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204946 AF
OSCILLO-
SCOPE
PROBE
D-134 HARNESS CONNECTOR :
HARNESS SIDE
76
85
65
72
71
73
82
75
81
74
63 64
66
70
69
68
67
78
87
79
88 89
80
77
86
62
61
83 84
ACX02131AB
NORMAL WAVEFORM
(V)
5
0
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-224
STEP 9. Check output shaft speed sensor connector C-02,
PCM connector D-134 and intermediate connector E-114
for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 10.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204746
CONNECTOR : C-02
C-02 (GR)
AB
1 2 3
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204176
CONNECTOR : E-114
BD
38
28
16
33
22
10
31
19
7
1
18
30
29
17
5
6
21
20
32
8
2
9
25
13
3
24
23
3435
1112
27
26
3637
14
4
15
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-225
STEP 10. Check harness for damage between output shaft
speed sensor connector C-02 terminal 2 and PCM
connector D-134 terminal 73.
Q: Is the harness wire in good condition?
YES : Go to Step 11.
NO : Repair or replace the harness wire.
STEP 11. Replace the output shaft speed sensor.
(1) Replace the output shaft speed sensor. Refer to GROUP
23B, Transmission
.
(2) Test drive the vehicle.
(3) Check for A/T diagnostic trouble code.
Q: Were any A/T DTCs set?
YES : Go to Step 12.
NO : The procedure is complete.
AC204746
CONNECTOR : C-02
C-02 (GR)
AB
1 2 3
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
ACX01223 AE
OUTPUT SHAFT
SPEED SENSOR
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-226
STEP 12. Replace the direct planetary carrier.
(1) Replace the direct planetary carrier. Refer to GROUP 23B,
Transmission
.
(2) Test drive the vehicle.
(3) Check for A/T diagnostic trouble code.
Q: Were any A/T DTCs set?
YES : An A/T DTC may have set due to external radio
frequency interference (RFI) possibly caused by
cellular phone activity, or aftermarket components
installed on the vehicle.
NO : The procedure is complete.
STEP 13. Replace the PCM.
(1) Replace the PCM.
(2) Test drive the vehicle.
(3) Check for A/T diagnostic trouble code.
Q: Were any A/T DTCs set?
YES : Go to Step 14.
NO : The procedure is complete.
STEP 14. Replace the valve body.
(1) Replace the valve body. Refer to GROUP 23B,
Transmission
.
(2) Test drive the vehicle.
(3) Check for A/T diagnostic trouble code.
Q: Were any A/T DTCs set?
YES : Go to Step 15.
NO : The procedure is complete.
AC204883
DIRECT
PLANETARY
CARRIER
AF
ACX02161AD
VALVE BODY ASSEMBLY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст