Mitsubishi Montero (2002-2004). Manual — part 1060
ANTI-LOCK BRAKING SYSTEM (ABS) DIAGNOSIS
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-111
DATA LIST REFERENCE TABLE
M1352011500401
The following items can be read by the scan tool
from the M-ASTC-ECU input data.
MUT-II SCAN
TOOL
DISPLAY*
ITEM
NO.
CHECK ITEM
CHECKING REQUIREMENTS
NORMAL VALUE
ACCUM
SW(PH)
77
Accumulator switch (PH) Accumulator fluid pressure
reduces to less than approx. 16.1
MPa
ON
Accumulator fluid pressure
reaches approx. 18.3 MPa
OFF
ACCUM
SW(PL)
76
Accumulator switch (PL) Accumulator fluid pressure
reduces to approx. 10.8 MPa or
less.
ON
M-ASTC OFF
SW
37
Active skid control
switch
Set the active skid control switch
to the neutral position
OFF
Turn the active skid control switch
to the OFF position
ON
M-ASTC ON
SW
38
Active skid control
switch
Set the active skid control switch
to the neutral position
OFF
Turn the active skid control switch
to the ON position
ON
BATT.
VOLTAGE
31
M-ASTC-ECU power
supply voltage
Ignition switch power supply
voltage and valve monitor voltage
6.5
− 22.3 V
ENGINE
SPEED
17
Engine speed
Drive the vehicle
The scan tool and the
tachometer readings
are approximately the
same
EN. TYPE/
DESTN
28
Engine model and
destination
−
6G75 NAS
FR SNSR
11
Front right ABS sensor
Drive the vehicle
Vehicle speeds
displayed on the
speedometer and
scan tool are identical.
FL SNSR
12
Front left ABS sensor
G SENS
VOLT 1
22
Output 1 from G sensor Drive the vehicle
-14.7
− 14.7 m/s
2
G SENS
VOLT 2
23
Output 2 from G sensor
G SENSOR
VOLT
19
Output from G sensor
(longitudinal
acceleration)
G
S(LATERAL)
20
Output from G sensor
(lateral acceleration)
IDLE POS.
SW
75
Closed throttle position
switch
Do not depress the accelerator
pedal
ON
Depress the accelerator pedal
OFF
ANTI-LOCK BRAKING SYSTEM (ABS) DIAGNOSIS
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-112
TR SWITCH
26
Transmission range
switch
Drive the vehicle
The shift lever position
indicator and the scan
tool readings are
equal
M/C PRESS.
SNSR
24
Master cylinder pressure
sensor
When depressing gradually the
brake pedal, the output value will
change.
Approximately 0.5 -
4.5 V
MOTOR RLY 79
Motor relay
Motor relay is operating
ON
Motor relay is not operating
OFF
RR SNSR
13
Rear right ABS sensor
Drive the vehicle
Vehicle speeds
displayed on the
speedometer and
scan tool are identical.
RL SNSR
14
Rear left ABS sensor
SHIFT
POSIT.
27
Shift position
Drive the vehicle
The shift lever position
indicator and the scan
tool readings are
equal
ST ANGLE
32
Steering wheel angle
Steering wheel angle
deg (approximately
the same as actual
steering wheel angle)
STOPLIGHT
SW
36
Stoplight switch
Depress the brake pedal.
ON
Release the brake pedal.
OFF
T/F MODE
30
Transfer position
Drive the vehicle.
the same as actual
transfer position
VALVE RLY
78
Valve relay
Valve relay is operating
ON
Valve relay is not operating
OFF
MUT-II SCAN
TOOL
DISPLAY*
ITEM
NO.
CHECK ITEM
CHECKING REQUIREMENTS
NORMAL VALUE
ANTI-LOCK BRAKING SYSTEM (ABS) DIAGNOSIS
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-113
ACTUATOR TEST REFERENCE
M1352011600378
CAUTION
When performing the item No. 09 [AIR BLEEDING
(1)] consecutively, keep the interval of 20 sec-
onds or more between respective bleeding oper-
ations.
The scan tool activates the following actuators for
testing.
NOTE: If the M-ASTC-ECU is inoperative, actuator
testing cannot be carried out.
NOTE: Actuator testing is only possible when the
vehicle is stationary. If the vehicle speed during actu-
ator testing exceeds 10 km/h (6 mph), forced actua-
tion will be canceled.
ACTUATOR TEST SPECIFICATIONS
MUT-II SCAN
TOOL DISPLAY
ITEM
NO.
CHECK ITEM
PARTS TO BE
ACTIVATED
ACTIVATION
WHEN THE
SYSTEM
FAILS
FR ABS VALVE
01
Solenoid valve for front-right wheel HBB select solenoid
valves and control
solenoid valves for the
respective channel
Disabled
FL ABS VALVE
02
Solenoid valve for front-left wheel
RR ABS VALVE
03
Solenoid valve for rear-right wheel
RL ABS VALVE
04
Solenoid valve for rear-left wheel
ABS AIR B.1
09
Air bleeding (1)
HBB select solenoid
valves and control
solenoid valve OUT (FR,
FL)
Disabled
ABS AIR B.2
10
Air bleeding (2)
HBB control solenoid
valve OUT (RR, RL)
Disabled
ANTI-LOCK BRAKING SYSTEM (ABS) DIAGNOSIS
TSB Revision
ANTI-LOCK BRAKING SYSTEM (ABS)
35B-114
ACX01113AC
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
1s
2s
ITEM No. 01 - 04 DRIVE PATTERN
CONTROL SOLENOID
VALVE IN
CONTROL SOLENOID
VALVE OUT
SELECT SOLENOID
VALVE (FR)
SELECT SOLENOID
VALVE (FL)
CORRESPONDING
WHEEL BRAKE PRESSURE
INCREASE
DECREASE
HOLD
INCREASE
ITEM No. 09, 10 DRIVE PATTERN
CONTROL SOLENOID
VALVE OUT (RH)*
CONTROL SOLENOID
VALVE OUT (LH)*
<ITEM No. 10 ONLY>
SELECT SOLENOID
VALVE (FR)
SELECT SOLENOID
VALVE (FL)
NOTE
*: WHEN CARRYING OUT ITEM No. 09, THE FRONT WHEELS ARE DRIVEN, AND WHEN
CARRYING OUT ITEM No. 10 THE REAR WHEELS ARE DRIVEN.
0.8s 0.8s
2.5s
0.8s
2.5s
0.8s 0.8s
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст