Mitsubishi Montero (2002-2004). Manual — part 1061

ANTI-LOCK BRAKING SYSTEM (ABS) DIAGNOSIS

TSB Revision

ANTI-LOCK BRAKING SYSTEM (ABS)

35B-115

CHECK AT M-ASTC-ECU

M1352011800402

TERMINAL VOLTAGE CHECK CHART

NOTE: There are two ECUs with the same shape inside the
floor console, one above the other. The upper ECU is the M-
ASTC-ECU. The lower ECU is the transfer-ECU.
NOTE: Do not measure terminal voltage for approximately
three seconds after the ignition switch is turned "ON." The M-
ASTC-ECU performs the initial check during that period.
1. Measure the voltages between terminals (4), (12), (56) or

(64) (ground terminals) and each respective terminal.

2. The terminal layouts are shown in the illustrations.

AC203901

AC204627AY

M-ASTC-ECU

M-ASTC-ECU CONNECTORS

TRANSFER-ECU

CONNECTOR
TERMINAL
NO.

SIGNAL

CHECKING REQUIREMENT

NORMAL
CONDITION

1

Control solenoid valve
OUT (Rear right wheel)

Ignition switch: ON

Battery positive
voltage

2

Control solenoid valve IN
(Rear right wheel)

Ignition switch: ON

Battery positive
voltage

3

Control solenoid valve
OUT (Front left wheel)

Ignition switch: ON

Battery positive
voltage

5

PI valve

Ignition switch: ON

Battery positive
voltage

6

Cut valve

Ignition switch: ON

Battery positive
voltage

7

Select solenoid valve
(Front right wheel)

Ignition switch: ON

Battery positive
voltage

8

Select solenoid valve
(Front left wheel)

Ignition switch: ON

Battery positive
voltage

10

Control solenoid valve IN
(Front left wheel)

Ignition switch: ON

Battery positive
voltage

19

Stoplight switch input

Stoplight switch: ON

Battery positive
voltage

Stoplight switch: OFF

2 V or less

ANTI-LOCK BRAKING SYSTEM (ABS) DIAGNOSIS

TSB Revision

ANTI-LOCK BRAKING SYSTEM (ABS)

35B-116

24

M-ASTC-ECU power
supply

Ignition switch: ON

Battery positive
voltage

42

Control solenoid valve IN
(Front right wheel)

Ignition switch: ON

Battery positive
voltage

43

Control solenoid valve
OUT (Front right wheel)

Ignition switch: ON

Battery positive
voltage

44

Control solenoid valve IN
(Rear left)

Ignition switch: ON

Battery positive
voltage

45

Control solenoid valve
OUT (Rear light wheel)

Ignition switch: ON

Battery positive
voltage

50

Pressure sensor power
supply

Ignition switch: ON

Approximately 5 V

55

Valve relay monitor

Ignition switch: ON

Battery positive
voltage

59

Pressure sensor

Ignition switch: ON

Approximately
0.14

− 4.85 V

62

ABS warning light output Ignition switch:

ON

When light is switched off Battery positive

voltage

When light is illuminated

2 V or less

74

Active skid control
system operation
warning light output

Ignition switch:
ON

When light is switched off Battery positive

voltage

When light is illuminated

2 V or less

75

2WD/4WD detection
switch input

Ignition switch:
ON

Transfer selector lever
position: 2H, 4H

Battery positive
voltage

Transfer selector lever
position: 4HLc, 4LLc

2 V or less

76

4LLc detection switch
input

Ignition switch:
ON

Transfer selector lever
position: 4LLc

Battery positive
voltage

Transfer selector lever
position: 2H, 4H, 4HLc

2 V or less

80

Center differential lock
switch input

Ignition switch:
ON

Transfer selector lever
position: 2H, 4H

Battery positive
voltage

Transfer selector lever
position: 4HLc, 4LLc

2 V or less

81

Brake warning light
output

Ignition switch:
ON

When light is switched off 2 V or less

When light is illuminated

Battery positive
voltage

CONNECTOR
TERMINAL
NO.

SIGNAL

CHECKING REQUIREMENT

NORMAL
CONDITION

ANTI-LOCK BRAKING SYSTEM (ABS) DIAGNOSIS

TSB Revision

ANTI-LOCK BRAKING SYSTEM (ABS)

35B-117

RESISTANCE AND CONTINUITY BETWEEN
HARNESS-SIDE CONNECTOR TERMINALS

NOTE: There are two ECUs with the same shape inside the
floor console, one above the other. The upper ECU is the M-
ASTC-ECU and has a blue connector. The lower ECU is the
transfer-ECU and has a green connector.
1. Turn the ignition switch to the "LOCK" (OFF) position and

disconnect the M-ASTC-ECU.

2. Check between the terminals indicated in the table below.
3. The terminal layouts are shown in the illustration.

86

2WD detection switch
input

Ignition switch:
ON

Transfer selector lever
position: 2H

Battery positive
voltage

Transfer selector lever
position: 4H, 4HLc, 4LLc

2 V or less

87

4H detection switch input Ignition switch:

ON

Transfer selector lever
position: 2H, 4LLc

Battery positive
voltage

Transfer selector lever
position: 4H, 4HLc

2 V or less

CONNECTOR
TERMINAL
NO.

SIGNAL

CHECKING REQUIREMENT

NORMAL
CONDITION

AC203901

AC204627AY

M-ASTC-ECU

M-ASTC-ECU CONNECTORS

TRANSFER-ECU

CONNECTOR
TERMINAL NO.

SIGNAL

NORMAL CONDITION

30

− 31

Front-left ABS sensor

1.0

− 1.5 kΩ

60

− 61

Rear-right ABS sensor

1.0

− 1.5 kΩ

46

− 47

Rear-left ABS sensor

1.0

− 1.5 kΩ

27

− 28

Front-right ABS sensor

1.0

− 1.5 kΩ

4

− body ground

Ground

Less than 2 ohms

22

− body ground

Ground

Less than 2 ohms

56

− body ground

Ground

Less than 2 ohms

64

− body ground

Ground

Less than 2 ohms

SPECIAL TOOLS

TSB Revision

ANTI-LOCK BRAKING SYSTEM (ABS)

35B-118

SPECIAL TOOLS

M1352000600426

TOOL

TOOL NUMBER AND
NAME

SUPERSESSION

APPLICATION

MB991502
Scan tool (MUT-II)

MB991496-OD

For checking of ABS
[Diagnostic trouble code
display when using the
scan tool (MUT-II)]

MB991348
Test harness set

MB991496-OD

For checking of G and
yawrate sensor

MB991223
Harness set
A:MB991219
Inspection harness

MB991223
MB991709-01

ABS sensor output
voltage measurement

B991502

MB991348

MB991223

A

AB

B

C

D