Mitsubishi Montero (2002-2004). Manual — part 330
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-367
.
TECHNICAL DESCRIPTION (COMMENT)
If the high-beam indicator light does not illuminate,
the high-beam indicator light bulb or the ETACS-
ECU may be defective.
.
TROUBLESHOOTING HINTS
• The high-beam indicator light bulb may be defec-
tive
• The ETACS-ECU may be defective
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
.
DIAGNOSIS
Required Special Tool:
• MB991223: Harness Set
STEP 1. Verify the headlight operation.
Q: Do the headlights illuminate?
YES : Go to Step 2.
NO : Repair the headlights first (Refer to
STEP 2. Check at ETACS-ECU connector D-224 in order to
check the high-beam indicator light circuit.
(1) Disconnect ETACS-ECU connector D-224, and measure at
the wiring harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Connect terminal 30 to ground.
Q: Does the high-beam indicator light illuminate?
YES : Replace the ETACS-ECU. Verify that the high-beam
indicator light illuminates normally.
NO : Go to Step 3.
AC204173
CONNECTORS : D-210, D-211
D-210
D-211(B)
AU
AC204174
CONNECTOR : D-224
D-224(B)
AG
AC204174
CONNECTOR : D-224
AD
D-224(B)
D-224(B)
HARNESS SIDE
21
23
24
22
32
3433
31
26
27
28
3029
38
39
40
36
37
25
35
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
AC101398 AB
CONNECTOR D-224
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-368
STEP 3. Check high-beam indicator light bulb.
(1) Remove the high-beam indicator light bulb.
(2) Verify that the high-beam indicator light bulb is not
damaged or burned out.
Q: Is the high-beam indicator light normal?
YES : Go to Step 4.
NO : Replace the bulb. Verify that the high-beam indicator
light illuminates normally.
STEP 4. Check the combination meter (printed-circuit
board).
(1) Remove the combination meter. Refer to GROUP 54A,
Combination Meters Assembly And Vehicle Speed Sensor
.
(2) Remove the high-beam indicator light bulb. Then measure
the resistance value between the bulb terminals.
(3) Install the bulb to the combination meter, and then measure
the resistance value between connector D-04 terminals 34
and 35. The measured resistance value should be roughly
the same as the value measured in Step (2).
Q: Are these two resistance values extremely different?
YES : Repair or replace the combination meter (printed
circuit board). Verify that the headlight-beam indicator
light illuminates normally.
NO (roughly the same) : Go to Step 5.
STEP 5. Check the fusible link (2) line of the power supply
circuit to the combination meter. Test at combination
meter connector D-04.
(1) Disconnect combination meter connector D-04 and
measure the voltage available at the wiring harness side of
the connector.
(2) Measure the voltage between terminal 34 and ground.
• The voltage should equal 12 volts (battery positive volt-
age).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 8.
NO : Go to Step 6.
46
45
44
43
42
41
32
31
39
47
38
37
36
35
34
33
40
AC100266AB
CONNECTOR D-04
AC204170
CONNECTOR : D-04
AD
D-04(GR)
HARNESS
SIDE
D-04(GR)
31
32
41 40
33
34
36
37
35
43
46 45 44
39
42
38
47
AC204461
41
42
43
44
45
46
37
38
39
40
31
32
33
34
35
36
47
AB
CONNECTOR D-04
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-369
STEP 6. Check combination meter connector D-04 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is combination meter connector D-04 in good
condition?
YES : Go to Step 7.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the high-beam indicator light
illuminates normally.
AC204170
CONNECTOR : D-04
AD
D-04(GR)
HARNESS
SIDE
D-04(GR)
31
32
41 40
33
34
36
37
35
43
46 45 44
39
42
38
47
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-370
STEP 7. Check the wiring harness between combination
meter connector D-04 (terminal 34) and the fusible link (2).
ACX02274
FUSIBLE LINK (2)
AC
BATTERY
AC204188
CONNECTORS : D-04, D-28
D-04(GR)
AK
HARNESS SIDE
D-04(GR)
D-28
D-28
31
32
41 40
33
34
36
37
35
43
46 45 44
39
42
38
47
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст