Mitsubishi Montero (2002-2004). Manual — part 823
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-161
STEP 3. Check the ground circuit to the SRS-ECU.
(1) Disconnect SRS-ECU connector E-08, and measure at the
wiring harness side.
CAUTION
Do not insert a test probe into the terminal from its front
side directly as the connector contact pressure may be
weakened.
(2) Check for continuity between E-08 harness terminal 7 and
body ground.
It should be less than 2 ohms.
Q: Does continuity exist?
YES : Go to Step 4.
NO : Go to Step 6.
STEP 4. Check the power supply circuit to the SRS-ECU.
(1) Disconnect SRS-ECU connector E-08, and measure at the
wiring harness side.
(2) Connect the negative battery terminal.
(3) Turn the ignition switch to the "ON" position.
CAUTION
Do not insert a test probe into the terminal from its front
side directly as the connector contact pressure may be
weakened.
(4) Measure the voltage between terminals 13, 16 and body
ground.
Voltage should measure 9 volts or more.
Q: Is the measured voltage within the specified range?
YES : Recheck the trouble symptom. If it is not solved,
replace the SRS-ECU. (Refer to
.) Then go
to Step 8.
NO : Go to Step 7.
ACX01478 AG
CONNECTOR: E-08
E-08 (Y)
AC201527
9 10 11 12
13 1415 16
1 2
3 4
5 6 7 8
17 18 19 20
E-08 HARNESS CONNECTOR:
HARNESS SIDE
AE
ACX01478 AG
CONNECTOR: E-08
E-08 (Y)
AC006265
13 14 15 16 17 18 19 20
5 6 7 8 9 10 11 12
1 2
3 4
AH
E-08 HARNESS
CONNECTOR:
HARNESS SIDE
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-162
STEP 5. Check the harness wires between SRS-ECU
connector E-08 (terminal No.20) and data link connector D-
118 (terminal No.7).
NOTE: After inspecting intermediate connector D-29 inspect
the wiring harness. If the intermediate connector D-29 is dam-
aged, repair or replace it. (Refer to GROUP 00E, Harness Con-
nector Inspection
.). Then go to Step 8.
Q: Are the harness wires between SRS-ECU connector E-
08 (terminal No.20) and data link connector D-118
(terminal No.7) in good condition?
YES : Go to step 8.
NO : Repair the harness wires between SRS-ECU
connector E-08 and data link connector D-118. Then
go to Step 8.
AC204231AF
CONNECTOR : D-29
D-29
D-29
33
22
11
28
17
16
15
14
13
12
25
23 24
26 27
3
1 2
4 5
21
20
19
18
29 30
32
31
7
6
8
10
9
ACX01478AH
CONNECTOR: E-08
E-08 (Y)
HARNESS
CONNECTOR:
HARNESS SIDE
AC204695
CONNECTOR : D-118
AC
D-118 (B)
ACCELLATOR PEDAL
1 2 3 4 5 6 7 8
9 10 11121314 15 16
D-118
CONNECTOR
(FRONT VIEW)
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-163
STEP 6. Check the harness wire between SRS-ECU
connector E-08 (terminal No.7) and ground.
Q: Is the harness wire between SRS-ECU connector E-08
(terminal No.7) and ground in good condition?
YES : Go to Step 8.
NO : Repair the harness wire between SRS-ECU
connector E-08 and ground. Then go to Step 8.
STEP 7. Check the harness wires between SRS-ECU
connector E-08 (terminal No.13 and 16) and ignition switch
connector D-204 (terminal No.2).
NOTE: After inspecting junction block connector D-210, D-209
and D-208 inspect the wiring harness. If the junction block con-
nector D-210, D-209 or D-208 is damaged, repair or replace it.
(Refer to GROUP 00E, Harness Connector Inspection
ACX01478AH
CONNECTOR: E-08
E-08 (Y)
HARNESS
CONNECTOR:
HARNESS SIDE
ACX01508
GROUND
AE
AC204257
CONNECTORS : D-208, D-209, D-210
AG
D-210
D-210 HARNESS CONNECTOR:
COMPONENT SIDE
JUNCTION BLOCK
(FRONT VIEW)
5 4
3 2
12
13
10
11
7
8
1
6
9
D-209
D-208
D-209 HARNESS CONNECTOR:
COMPONENT SIDE
D-208 HARNESS CONNECTOR:
COMPONENT SIDE
1
2
3
5
6
4
5 4 3
2
12
13
10
11
7
8
1
6
9
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSIS
52Bb-164
Q: Are the harness wires between SRS-ECU connector E-
08 (terminal No.13 and 16) and ignition switch
connector D-204 (terminal No.2) in good condition?
YES : Go to Step 8.
NO : Repair the harness wires between SRS-ECU
connector E-08 and ignition switch connector D-204.
Then go to Step 8.
STEP 8. Retest the system.
Q: Does the scan tool communicate normally with the SRS
system?
YES : The procedure is complete. (If no malfunctions are
not found in all steps, an intermittent malfunction is
suspected. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
NO : There is no action to be taken.
ACX01478 AD
CONNECTOR: E-08
AC204226AE
CLOCK SPRING
CONNECTOR: D-204
D-204
HARNESS
CONNECTOR:
COMPONENT
SIDE
2
5
6
3
4
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст