Mitsubishi Montero (2002-2004). Manual — part 988
SYMPTOM PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
SYMPTOM PROCEDURES
23Ad-63
STEP 21. Check shift switch assembly connector E-115 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 22.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
STEP 22. Measure the switch output voltage at PCM
connector D-134.
(1) Disconnect connector D-134 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 68 and ground.
• The voltage should measure battery positive voltage
when the selector lever is downshift and hold.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage battery positive voltage?
YES : Go to Step 14.
NO : Go to Step 23.
AC204176
CONNECTOR : E-115
BE
8
3
4 5
1
2
6 7
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204918 BH
D-134 HARNESS CONNECTOR :
HARNESS SIDE
80
87
73
66
67
65
74
81
75
82
62 61
72
68
69
70
71
78
85
77
84 83
76
79
86
63
64
89 88
SYMPTOM PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
SYMPTOM PROCEDURES
23Ad-64
STEP 23. Check PCM connector D-134 and intermediate
connector E-114 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 24.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204176
CONNECTOR : E-114
BD
38
28
16
33
22
10
31
19
7
1
18
30
29
17
5
6
21
20
32
8
2
9
25
13
3
24
23
3435
1112
27
26
3637
14
4
15
SYMPTOM PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
SYMPTOM PROCEDURES
23Ad-65
STEP 24. Check harness for open circuit or short circuit to
ground between PCM connector D-134 terminal 68 and
shift switch assembly connector E-115 terminal 8.
Q: Is the harness wire in good condition?
YES : Go to Step 25.
NO : Repair or replace the harness wire.
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204176
CONNECTOR : E-115
BE
8
3
4 5
1
2
6 7
SYMPTOM PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
SYMPTOM PROCEDURES
23Ad-66
STEP 25. Using scan tool MB991502, check data list item
67: Select Switch, item 68: Shift Switch (Up), item 69: Shift
Switch (Down).
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check the following items in the data list.
a. item 67: Select Switch
b. item 68: Shift Switch (Up)
c. item 69: Shift Switch (Down)
• The switches above are displayed, depending on the
selector lever condition as shown in the table.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the switch operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use Troubleshooting/
Inspection Service Points
− How to Cope with
Intermittent Malfunction
NO : Replace the PCM.
SELECTOR
LEVER
OPERATION
DATA LIST ITEM
67
68
69
D range
OFF
OFF
OFF
Sport mode
ON
OFF
OFF
Upshift and hold
the selector lever
ON
ON
OFF
Downshift and
hold the selector
lever
ON
OFF
ON
ACX01539AD
MB991502
16-PIN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст