Mitsubishi Montero (2002-2004). Manual — part 987
SYMPTOM PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
SYMPTOM PROCEDURES
23Ad-59
STEP 14. Check PCM connector D-134 for loose, corroded
or damaged terminals, or terminals pushed back in the
connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 25.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
STEP 15. Check the shift switch assembly.
Refer to
, Transmission Control.
Q: Is the switch operating properly?
YES : Go to Step 16.
NO : Replace the shift switch assembly. Refer to
, Transmission Control.
STEP 16. Check shift switch assembly connector E-115 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 17.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204176
CONNECTOR : E-115
BE
8
3
4 5
1
2
6 7
SYMPTOM PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
SYMPTOM PROCEDURES
23Ad-60
STEP 17. Measure the switch output voltage at PCM
connector D-134.
(1) Disconnect connector D-134 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 77 and ground.
• The voltage should measure battery positive voltage
when the selector lever is upshift and hold.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage battery positive voltage?
YES : Go to Step 14.
NO : Go to Step 18.
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204918 BN
D-134 HARNESS CONNECTOR :
HARNESS SIDE
80
87
73
66
67
65
74
81
75
82
62 61
72
68
69
70
71
78
85
77
84 83
76
79
86
63
64
89 88
SYMPTOM PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
SYMPTOM PROCEDURES
23Ad-61
STEP 18. Check PCM connector D-134 and intermediate
connector E-114 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 19.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204176
CONNECTOR : E-114
BD
38
28
16
33
22
10
31
19
7
1
18
30
29
17
5
6
21
20
32
8
2
9
25
13
3
24
23
3435
1112
27
26
3637
14
4
15
SYMPTOM PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
SYMPTOM PROCEDURES
23Ad-62
STEP 19. Check harness for open circuit or short circuit to
ground between PCM connector D-134 terminal 77 and
shift switch assembly connector E-115 terminal 7.
Q: Is the harness wire in good condition?
YES : Go to Step 25.
NO : Repair or replace the harness wire.
STEP 20. Check the shift switch assembly.
Refer to
, Transmission Control.
Q: Is the switch operating properly?
YES : Go to Step 21.
NO : Replace the shift switch assembly. Refer to
, Transmission Control.
AC204681AC
CONNECTOR: D-134
D-134 (GR)
61 62
63 64
65 66 67 68 69 70 71 72 73
82
89
81
88
80
79
78
77
87
86
85
76
75
74
84
83
AC204176
CONNECTOR : E-115
BE
8
3
4 5
1
2
6 7
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст