Mitsubishi Montero (2002-2004). Manual — part 26
MARK
TSB Revision
EXTERIOR
51-31
2. Installation procedure
(1) Use 3M
ä AAD Part number 8906 or equivalent to clean
the mark installation surfaces on the body.
CAUTION
When attaching the marks, the ambient temperature
should be 20
− 38°C (60 − 100°F) and the air should be
completely free of dust. If the ambient temperature is lower
than 20
°C (60°F), the marks and the places on the vehicle
body where the marks are to be attached should be heated
to 20
− 38°C (60 − 100°F).
(2) Peel off the backing paper from the reverse side of the
marks, carefully attach the marks to the vehicle body in
the exact position shown.
AC204137
12 (0.5)
PRESS LINE
41 (1.6)
FRONT DOOR OPENING LINE
PRESS LINE
FRONT DOOR OPENING LINE
12 (0.5)
18.5(0.7)
UNITS: mm (in)
MONTERO MARK, GRADE MARK (XLS, LIMITED)
NOTE : RH side is symmetrical on LH side.
AB
AC204140
SIDE OUTER PANEL END LINE
UNITS: mm (in)
SIDE OUTER PANEL END LINE
85 (3.4)
35 (1.4)
125 (4.9)
85 (3.4)
35 (1.4)
125 (4.9)
THREE-DIAMOND MARK, GRADE MARK (XLS, LIMITED)
CONBINATION LIGHT
CONBINATION LIGHT
BACK DOOR END LINE
BACK DOOR END LINE
AB
DOOR MIRROR
TSB Revision
EXTERIOR
51-32
DOOR MIRROR
SPECIAL TOOL
M1511000600100
DOOR MIRROR
REMOVAL AND INSTALLATION
M1511006400171
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB990784 Ornament
remover
General service tool
Removal of air outlet
assembly
MB990784
AC000440
1
2
3
4
1
1
5
6
A
A
B
B
CLIP
CLIP
SECTION A – A
SECTION B – B
AB
DOOR MIRROR REMOVAL STEPS
1. DELTA COVER, INNER
2. TWEETER COVER
3. DOOR MIRROR ASSEMBLY
<<A>> >>A<<
4. MIRROR
REMOTE CONTROLLED MIRROR
SWITCH REMOVAL STEPS
5. AIR OUTLET ASSEMBLY (REFER
TO GROUP 52A - INSTRUMENT
PANEL
6. REMOTE CONTROLLED MIRROR
SWITCH
DOOR MIRROR
TSB Revision
EXTERIOR
51-33
REMOVAL SERVICE POINT
.
<<A>> MIRROR REMOVAL
Push the top of the mirror with your hand to tilt it and attach the
protective tape as shown in the illustration. Then insert a flat-
tipped screwdriver in between the notch at the rear of the mirror
and the pivot plate, and disengage the bottom of the mirror.
INSTALLATION SERVICE POINT
.
>>A<< MIRROR INSTALLATION
While supporting the clip position on the underside of the pivot
plate with a flat-tipped screwdriver, press the clip at the front of
the mirror to engage the bottom of the mirror.
AC000441
00007256
MIRROR
FLAT-TIPPED
SCREWDRIVER
SECTION A – A
PIVOT PLATE
NOTCH
PROTECTIVE
TAPE
A
A
A
A
AB
AC000442
00007258
MIRROR
FLAT-TIPPED
SCREWDRIVER
SECTION A – A
PIVOT PLATE
A
A
A
A
AB
DOOR MIRROR
TSB Revision
EXTERIOR
51-34
INSPECTION
M1511019100266
REMOTE CONTROLLED MIRROR ASSEMBLY
CHECK
REMOTE CONTROLLED MIRROR SWITCH
CONTINUITY CHECK
BATTERY CONNECTION
SPECIFIED
CONDITION
•Connect terminal 6 to the
negative battery terminal
•Connect terminal 4 to the positive
battery terminal
Mirror glass should
face upward
•Connect terminal 4 to the
negative battery terminal
•Connect terminal 6 to the positive
battery terminal
Mirror glass should
face downward
•Connect terminal 5 to the
negative battery terminal
•Connect terminal 6 to the positive
battery terminal
Mirror glass should
face to the right
•Connect terminal 6 to the
negative battery terminal
•Connect terminal 5 to the positive
battery terminal
Mirror glass should
face to the left
AC000443
SWITCH POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
Left side
Up
1
− 6, 9 − 11
Less than 2
ohms
Down
1
− 11, 6 − 9
Right
1
− 6, 9 − 10
Left
1
− 10, 6 − 9
Right side Up
1
− 6, 3 − 9
Down
1
− 3, 6 − 9
Right
1
− 6, 2 − 9
Left
1
− 2, 6 − 9
Illumination
5
− 8
AC000444
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст