Mitsubishi Montero (2002-2004). Manual — part 25
REAR WIPER AND WASHER
TSB Revision
EXTERIOR
51-27
REAR WIPER AND WASHER
REMOVAL AND INSTALLATION
M1511008800078
NOTE: For removal and installation of the wiper and
washer switch, refer to GROUP 54A, Column switch
AC203982 AB
7
4.9 ±
0.7 N
•
m
44 ± 6 in-lb
4
5
3
2
6
1
8.0 ±
1.2 N
•
m
71 ± 10 in-lb
4.9 ±
0.7 N
•
m
44 ± 6 in-lb
4.9 ±
0.7 N
•
m
44 ± 6 in-lb
REAR WIPER MOTOR ASSEMBLY
REMOVAL STEPS
• TOOLBOX BRACKET, UPPER
(REFER TO GROUP 42, DOOR
TRIM AND WATERPROOF FILM
.)
>>B<<
1. REAR WIPER ARM AND BLADE
ASSEMBLY
>>A<<
2. GROMMET
3. REAR WIPER MOTOR ASSEMBLY
REAR WASHER TANK ASSEMBLY
AND REAR WASHER MOTOR
REMOVAL STEPS
• WATERPROOF FILM (REFER TO
GROUP 42A, DOOR TRIM AND
WATERPROOF FILM
4. REAR WASHER TANK ASSEMBLY
5. REAR WASHER MOTOR
REAR WASHER HOSE REMOVAL
STEPS
6. WASHER NOZZLE
• WATERPROOF FILM (REFER TO
GROUP 42A, DOOR TRIM AND
WATERPROOF FILM
7. REAR WASHER HOSE
REAR WASHER TANK ASSEMBLY
AND REAR WASHER MOTOR
REMOVAL STEPS (Continued)
REAR WIPER AND WASHER
TSB Revision
EXTERIOR
51-28
INSTALLATION SERVICE POINTS
.
>>A<< GROMMET INSTALLATION
Install so that the matching mark on the grommet is aligned
with the notch in the mounting hole.
.
>>B<< REAR WIPER ARM AND BLADE ASSEMBLY
INSTALLATION
Install so that the end of the wiper blade stops at the specified
position (standard value).
Standard value (A): 25
± 35 mm (1.0 ± 1.4 inches)
INSPECTION
M1511019100255
REAR WIPER MOTOR CHECK
The rear wiper motor assembly should be installed to the vehi-
cle body and the harness connector should be disconnected
when checking the wiper motor.
.
Wiper Motor Operation
Connect the battery to the wiper motor as shown in the illustra-
tion, and then check the operation of the wiper motor.
.
Wiper Motor at Stop Position Operation
1. Operate the wiper motor by the same method as described
in the check procedure above. Then, while the motor is
operating, disconnect the battery to make the wiper motor
stop.
2. Reconnect the battery as shown in the illustration, and then
check whether the wiper motor automatically stops in the
correct stop position after it has been running.
X1159CA
ACX00452
NOTCH
MATCHING
MARK
GROMMET
AB
X1137CA
ACX00451AB
REAR WASHER NOZZLE
A
END OF CERAMIC LINE
REAR WIPER BLADE
1 2 3 4
1 2 3 4
ACX00453
OPERATION CHECK
AB
STOP POSITION CHECK
REAR WIPER AND WASHER
TSB Revision
EXTERIOR
51-29
REAR WASHER MOTOR CHECK
1. The rear washer tank assembly should be installed and the
rear washer tank should be filled with water when checking
the washer motor.
2. Check that water is sprayed out strongly when system
voltage is applied to terminal (2) and terminal (1) is
grounded.
REAR WASHER NOZZLE SPRAY DIRECTION
CHECK
Move the nozzle to adjust so that the water is sprayed out
within the range shown in the illustration.
CAUTION
Be careful not to damage the spray hole of the nozzle
when inserting the flat-tipped screwdriver into the spray
hole of the nozzle.
• To adjust the vertical direction of the rear washer nozzle
spray position, insert a flat-tipped screwdriver into the spray
hole of the rear washer nozzle and move it in the direction
of the arrow.
1
2
ACX00455
X1138CA
ACX00457
UNITS: mm ( in )
140 ( 5.5 )
95 ( 3.8 )
10 ( 0.4 )
85 ( 3.4 )
AB
REAR WASHER NOZZLE
CENTER OF VEHICLE
EDGE OF BACK DOOR WINDOW GLASS
X1207CA
ACX00456 AB
REAR WASHER
NOZZLE
FLAT-TIPPED
SCREWDRIVER
MARK
TSB Revision
EXTERIOR
51-30
REAR WIPER AND WASHER SWITCH CHECK
MARK
REMOVAL AND INSTALLATION
M1511011800249
Required Special Tool:
• MB990528: Stripe Tape Spatula
INSTALLATION SERVICE POINT
.
>>A<< MARK INSTALLATION
1. Installation position
Attach to the position shown in the illustration.
SWITCH POSITION
TERMINAL
CONNECTION
SPECIFIED
CONDITION
OFF
4
− 6, 5 − 6
Open circuit
Rear washer switch ON
5
− 6
Less than 2
ohms
Rear wiper switch ON
4
− 6
1
6
8
11
10
9
7
5
4
3
2
AC000417AB
AC203779
1
2
3 4
AB
>>A<< 1. MONTERO MARK
>>A<<
2. GRADE MARK (SIDE)
>>A<<
3. THREE-DIAMOND MARK
>>A<<
4. GRADE MARK (REAR)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст