Mitsubishi Montero (2002-2004). Manual — part 270
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-127
INSPECTION PROCEDURE C-5: Central Door Locking System: All the doors do not lock with just the
driver's inside lock knob operation.
.
TECHNICAL DESCRIPTION
The driver's door lock actuator switch or the ETACS-
ECU may be defective.
.
TROUBLESHOOTING HINTS
• The driver's door lock actuator switch may be
defective
• The ETACS-ECU may be defective
• The wiring harness or connectors may have
loose, corroded or damaged terminals, or termi-
nals pushed back in the connector
Central Door Lock (Door Lock Actuator Switch) Circuit
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-128
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991502: Scan Tool (MUT-II)
Check the input signal (by using the pulse check mode of
the monitor.)
Check the input signals from the driver's door lock actuator
switch.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector
(16-pin).
(2) Operate scan tool MB991502 as follows:
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "PULSE CHECK."
(3) Lock or unlock the driver's inside lock knob.
(4) Check scan tool MB991502 sounds or not.
Q: Does scan tool MB991502 sound when the driver's
inside lock knob is locked or unlocked, or the
passenger's side lock knob is moved from the lock to
the unlock position?
YES : Replace the ETACS-ECU. Verify that all the doors
can be locked or unlocked by operating the driver's
inside lock knob.
NO : Refer to Inspection Procedure O-6 "ETACS-ECU
does not receive a signal from the driver's door lock
actuator switch
ACX01539
16-pin
MB991502
AI
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-129
INSPECTION PROCEDURE C-6: Central Door Locking System: Forgotten key prevention function
does not work normally.
NOTE: This troubleshooting procedure requires the
use of scan tool MB991502 and SWS monitor kit
MB991862. For details on how to use the SWS mon-
itor, refer to "How to use SWS monitor
.
CIRCUIT OPERATION
The ETACS-ECU operates the forgotten key preven-
tion function according to the following switches:
• Key reminder switch: OFF
• Driver's or front passenger's door switch: ON
• Driver's door lock actuator switch: being turned
ON
The ETACS-ECU activates the forgotten key preven-
tion function under the following conditions:
• Ignition key: inserted into the ignition key cylinder
• Driver's or front passenger's door: open
• Driver’s or front passenger’s door lock: being
locked electrically
• Driver’s door lock: being locked manually
.
TECHNICAL DESCRIPTION (COMMENT)
If the forgotten key prevention function does not
work normally, the input circuit from the switches or
the ETACS-ECU may be defective.
.
TROUBLESHOOTING HINTS
• The key reminder switch may be defective
• The driver's or front passenger's door switch may
be defective
• The driver's door lock actuator switch may be
defective
• The ETACS-ECU may be defective
• The wiring harness or connectors may have
loose, corroded or damaged terminals, or termi-
nals pushed back in the connector
Forgotten Key Prevention Circuit
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-130
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991502: Scan Tool (MUT-II)
• MB991862: SWS Monitor Kit
STEP 1. Use scan tool MB991502 to select "ECU COMM
CHK" on the SWS monitor display.
Check the ETACS-ECU.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector
(16-pin).
(2) Connect the SWS monitor kit MB991862 to the data link
connector (13-pin).
(3) Turn the ignition switch to the "LOCK" (OFF) position.
(4) Operate scan tool MB991502 as follows:
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "SWS MONITOR."
4. Select "ECU COMM CHK".
(5) Check scan tool MB991502 should show "OK" on the
"ETACS ECU" menu.
Q: Is "OK" displayed on the "ETACS ECU" menu?
YES : Go to Step 2.
NO : Refer to Inspection Procedure A-3 "Communication
with ETACS-ECU is not possible
AC204222AB
16-pin
13-pin
MB991502
MB991862
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст