Mitsubishi Montero (2002-2004). Manual — part 990
SYMPTOM PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
SYMPTOM PROCEDURES
23Ad-71
STEP 4. Measure the switch output voltage at PCM
connector D-133 by backprobing.
(1) Do not disconnect connector D-133.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 55 and ground by
backprobing.
• The voltage should measure battery positive voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage battery positive voltage?
YES : Go to Step 5.
NO : Go to Step 7.
AC204681AD
CONNECTOR: D-133
D-133 (GR)
31 32
33 34
35 36 37 38 39 40 41 42 43
44 45 46 47 48 49
50 51
52 53
54 55 56
57 58
AC204918 BD
D-133 HARNESS CONNECTOR :
HARNESS SIDE
50
58
43
36 37
35
44
52
45
53
32
31
42
38 39 40 41
46
55
48
54
51
47
49
56
33 34
57
SYMPTOM PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
SYMPTOM PROCEDURES
23Ad-72
STEP 5. Check PCM connector D-133 and intermediate
connector E-114 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 6.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204681AD
CONNECTOR: D-133
D-133 (GR)
31 32
33 34
35 36 37 38 39 40 41 42 43
44 45 46 47 48 49
50 51
52 53
54 55 56
57 58
AC204176
CONNECTOR : E-114
BD
38
28
16
33
22
10
31
19
7
1
18
30
29
17
5
6
21
20
32
8
2
9
25
13
3
24
23
3435
1112
27
26
3637
14
4
15
SYMPTOM PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
SYMPTOM PROCEDURES
23Ad-73
STEP 6. Check harness for open circuit between 4LLc
detection switch connector C-05 terminal 1 and PCM
connector D-133 terminal 55.
Q: Is the harness wire in good condition?
YES : Go to Step 9.
NO : Repair or replace the harness wire.
AC204395
CONNECTOR : C-05
AG
C-05 (BR)
C-05
1
AC204681AD
CONNECTOR: D-133
D-133 (GR)
31 32
33 34
35 36 37 38 39 40 41 42 43
44 45 46 47 48 49
50 51
52 53
54 55 56
57 58
SYMPTOM PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
SYMPTOM PROCEDURES
23Ad-74
STEP 7. Check PCM connector D-133 and intermediate
connector E-114 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES : Go to Step 8.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204681AD
CONNECTOR: D-133
D-133 (GR)
31 32
33 34
35 36 37 38 39 40 41 42 43
44 45 46 47 48 49
50 51
52 53
54 55 56
57 58
AC204176
CONNECTOR : E-114
BD
38
28
16
33
22
10
31
19
7
1
18
30
29
17
5
6
21
20
32
8
2
9
25
13
3
24
23
3435
1112
27
26
3637
14
4
15
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст