Mitsubishi Montero (2002-2004). Manual — part 308
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-279
INSPECTION PROCEDURE H-3: Rear Wiper and Washer: When the selector lever is moved to "R"
position during the rear wiper operation, the rear wiper does not operate at the continuous mode.
NOTE: This troubleshooting procedure requires use
of scan tool MB991502 and SWS monitor kit
MB991862. For details on how to use the SWS mon-
itor, refer to "How to use SWS monitor
.
CIRCUIT OPERATION
The ETACS-ECU operates the rear wiper consecu-
tively approximately twice when the selector lever is
moved to "R" position while the rear wiper is turned
on.
.
TECHNICAL DESCRIPTION (COMMENT)
If the rear wiper does not work consecutively approx-
imately twice, the transmission range switch ("R"
position) or the ETACS-ECU may be defective.
.
TROUBLESHOOTING HINTS
• The transmission range switch may be defective
• The ETACS-ECU may be defective
• The wiring harness may be damaged or the con-
nectors may have loose, corroded or damaged
terminals, pushed back in the connector
"R" Position during Rear Wiper Operation Circuit
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-280
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991502: Scan Tool (MUT-II)
• MB991862: SWS Monitor Kit
STEP 1. Verify the rear wiper operation.
Q: Does the rear wiper operate normally?
YES : Go to Step 2.
NO : Refer to Inspection Procedure H-1 "Rear wiper does
not work at all
STEP 2. Check the input signal by using "FUNCTION
DIAG." menu of the SWS monitor.
Set each switch to the following condition before checking input
signal from the transmission range switch ("R" position).
• Ignition switch: ON
• Rear wiper switch: ON
• Shift position: "R" position
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector
(16-pin).
(2) Connect SWS monitor kit MB991862 to the data link
connector (13-pin).
(3) Operate scan tool MB991502 according to the procedure
below to display "REV. INTERLOCK."
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "SWS MONITOR."
4. Select "FUNCTION DIAG."
5. Select "REAR WIPER."
6. Select "REV. INTERLOCK."
(4) Check that normal conditions are displayed on the item
described in the table below.
Q: Are normal conditions displayed?
YES : Replace the ETACS-ECU. When the selector lever is
moved to the "R" position, the rear wiper should
operate consecutively approximately twice.
NO : Refer to Inspection Procedure O-4 "ETACS-ECU
does not receive "R" position signal from the
transmission range switch
ITEM NO.
ITEM NAME
NORMAL CONDITION
ITEM 41
PNP SW (R)
ON
AC204222AB
16-pin
13-pin
MB991502
MB991862
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-281
INSPECTION PROCEDURE H-4: Rear Wiper and Washer: Rear washer does not operate.
NOTE: This troubleshooting procedure requires use
of scan tool MB991502 and SWS monitor kit
MB991862. For details on how to use the SWS mon-
itor, refer to "How to use SWS monitor
Rear Washer Drive Circuit
AC000759
CONNECTOR: D-111
AC
ACX02285
CONNECTOR: D-221
AU
JUNCTION BLOCK (FRONT VIEW)
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-282
.
CIRCUIT OPERATION
The rear washer switch sends a signal through the
column-ECU (incorporated in the column switch) to
the ETACS-ECU. If the column-ECU sends a rear
washer switch "ON" signal to the ETACS-ECU, the
ETACS-ECU turns on the relay (incorporated in the
ETACS-ECU), thus causing the rear washer motor to
be turned on.
.
TECHNICAL DESCRIPTION (COMMENT)
If the rear washer does not work normally, the rear
washer motor, the column switch (windshield wiper
and washer switch) or the front-ECU may be defec-
tive.
.
TROUBLESHOOTING HINTS
• The rear washer motor may be defective
• The column switch (windshield wiper and washer
switch) may be defective
• The ETACS-ECU may be defective
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991502: Scan Tool (MUT-II)
• MB991862: SWS Monitor Kit
STEP 1. Verify the rear wiper operation.
Q: Does the rear wiper operate normally?
YES : Go to Step 2.
NO : Refer to Inspection Procedure H-1 "Rear wiper does
not work at all
ACX02286
CONNECTOR: D-222
AC
JUNCTION BLOCK (REAR VIEW)
ACX02290
CONNECTOR: G-10
AB
ACX02293
CONNECTOR: I-08
AE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст